User manual MIELE KM 5773

[. . . ] Operating and Installation instructions Ceramic Cooktop with induction KM 5773 To prevent accidents and appliance damage, read these instructions before installation or use. V M. -Nr. 49 3 Guide to the cooktop Cooktop abcde burners Sensors Control panel f Power selector g Booster h Turning on the timer, switching between the functions, selecting a burner j Child Safety Lock k Setting the time / Selecting the memory program l Cooktop ON/OFF m Memory function Indicator: i Lock 4 Guide to the cooktop Burner indicator n Display: 0 = 1 to 12 = # = ß = F = A = P0 etc. = Burner is ready for use Power level Residual heat Missing or not suitable cookware (see "Induction") Error/Fault (see "Safety turn off") Auto-heat with extended power level range Program (see "Programming") Status (see "Programming") o Indicator for extended power level (see "Programming") p Lighting circle The number of segments lit corresponds to the selected power setting (exception: see "Auto-heat"). q Segment for booster 5 Guide to the cooktop Timer/Memory display r Indicator for burner assignment, e. g. [. . . ] While the residual heat indicators are lit: Do not touch the burners and do not set items which could get damaged by heat on the burners. Please note, that the residual heat indicators will not light during a fault, even if the burners are still hot. Turning off the cooktop ^ Touch the s On/Off cooktop sensor. For the burners which are still hot the residual heat indicator shows in the respective display. 23 Timer and Memory function Introduction The hob is fitted with: - Timer function - Automatic switch-off for the burners zones (Timer function) - Memory function. Use the sensor to reduce the time from 99 to 00 and the + sensor to increase the time from 00 to 99. The display can be put back to 00 by touching - and + at the same time. On all functions, 00 will appear in the display for a few seconds at the end of the time, and an audible tone will sound at the same time. To turn the audible tone off before it has finished, touch the m sensor. Setting the timer The timer can be used with the hob switched on or off. ^ Touch the - or + sensor until the time you require appears in the display, e. g. The time remaining can be seen in the display and changed at any time by touching - or +. 24 Timer and Memory function Switching a burner off automatically You can set a time at the end of which a given burner will switch off automatically. This automatic switch-off function can be used on all of the burners at the same time. ^ Touch the m sensor until the indicator lamp for the selected zone flashes (back right). If more than one burner is switched on, the indicator lamps will light up clockwise beginning with the front left zone. ^ Touch the - or + sensor until the time you require appears in the display, e. g. If more than one switch-off time is programmed, the shortest time remaining will show in the display, and the indicator lamp for that particular burner will flash. If you want to check on the remaining time for another zone, touch the m sensor until the indicator lamp for the zone you require flashes. Timer starting value The timer is set at the factory to start at 00 when the + or - sensor is touched. This setting can be adjusted so that the time you last used appears in the display when you press + or - (see "Programming - P14. "). Example: If P14, S1 is programmed, and the last time thetimer was used was for 5 minutes, 00 will appear in the display when you switch on the Timer; when you then touch + or -, the display will change to 05. You can still select any time you want, even if you have adjusted the timer default setting. The time then counts down in minutes. The time remaining can be seen in the Timer/Memory display and changed at any time by touching - or +. If you want to set another burner to switch off automatically, follow the same steps as described above. 25 Timer and Memory function Memory function All settings, which are set to a burner from turning on until turning off, can be recorded in a memory program. 5 frequently used operations can be recorded, but only one at a time can be recorded and used. To record a new program when all 5 programs are taken, one program must be deleted. [. . . ] If the manufacturer of these items states a different figure, always adhere to the greater distance. Their measurements should be given in their operating and installation instructions. wok burner and electric cooktop, and they have different minimum safety distances always select the greater distance. 43 Installation Cooktops flush with the countertop Frame/Facet cooktops a Wall b Wall covering c Back splash strip d Countertop e Countertop cut-out f 2" (50 mm) minimum distance 44 Installation Installation dimensions (514m ) 20 1/4" m) 36 (9 5/8" 5/16 ) m (8m ) mm (46 " m 30m b ") /16 ß 3 4mm ßR ( 0 (0502" mm ) (50 1911/16 0 +1 - "+1/1 - 6" mm ) 36(916 - " /16 ) " +1 /16 - mm 1 +1 0 (0502" mm ) a b 01 ( 03 6" 3/1 c 3 3/8" a ) (46mm) (86mm) (124 0mm ) 3/4" m 0m 113/16" 9 6" 1/1 ( 0 23 m m ) d a Front b Installation height c Installation height power cord d Power cord 45 Installation Cut out ^ Make the countertop cut-out following the dimensions given in the illustration. Remember to maintain a minimum distance of 2" (50 mm) between the rear wall on the right or left side. [. . . ]