User manual MIELE KM 5773 IND

[. . . ] Operating and Installation instructions Ceramic hobs with induction KM 5773 To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. Gi M. -Nr. 52 3 Guide to the appliance Hob abcde Cooking zones Sensor switches Control panel f For setting the power level g Booster h Sensor for setting the timer, changing between functions, and selecting a cooking zone j Safety lock k For setting the time/ Selecting a memory programme l Hob ON/OFF m Memory function Indicator lamp for i Safety lock 4 Guide to the appliance Cooking zone display n Displays: 0 = 1 to 12 = # = ß = F A P0 etc. = = = = Cooking zone ready for use Power levels Residual heat No pan on cooking zone or pan unsuitable (see "Induction") Fault (see "Safety switch-off") Auto heat-up when the power level range has been extended Programme (see "Programming") Status (see "Programming") o Indicator lamp for extending the power level range (see "Programming") p Light-ring: The number of curved lines lit up equates to the power level chosen (exception: see "Cooking with Auto heat-up") q This segment lights up when a booster is engaged 5 Guide to the appliance Timer/Memory display r Indicator lamp for relevant zone, e. g. the rear right cooking zone s Display for Time/Memory programme 00 to 99 = Time P1 to P5 = Memory programme t Memory programme indicator lamp Cooking zones Cooking zone KM 5773 minimum to maximum C in cm* 16 -23 10 - 16 18 - 28 14 - 20 14 - 20 Rating in watts for 230 V** normal: with booster: normal: with booster: normal: with booster: normal: with booster: normal: with booster: Total: 2300 3200 1400 1800 2400 3200 1850 2500 1850 2500 10600 y w b x z * Pan bases should be slightly larger than the smallest diameter shown in the chart. [. . . ] The display can be put back to 00 by touching - and + at the same time. On all functions, 00 will appear in the display for a few seconds at the end of the time, and an audible tone will sound at the same time. To turn the audible tone off before it has finished, touch the m sensor. Setting the minute minder The minute minder can be used with the hob switched on or off. ^ Touch the - or + sensor until the time you require appears in the display, e. g. The time remaining can be seen in the display and changed at any time by touching - or +. 26 Timer and Memory function Switching a cooking zone off automatically You can set a time at the end of which a given cooking zone will switch off automatically. This automatic switch-off function can be used on all of the cooking zones at the same time. ^ Touch the m sensor until the indicator lamp for the selected zone flashes (back right). If more than one cooking zone is switched on, the indicator lamps will light up clockwise beginning with the front left zone. ^ Touch the - or + sensor until the time you require appears in the display, e. g. If more than one switch-off time is programmed, the shortest time remaining will show in the display, and the indicator lamp for that particular cooking zone will flash. If you want to check on the remaining time for another zone, touch the m sensor until the indicator lamp for the zone you require flashes. Timer starting value The timer is set at the factory so that it starts with 01 or 99 when the + or sensor is touched. This setting can be adjusted so that the time you last used appears in the display when you press + or - (see "Programming - P14. "). Example: If P14, S1 is programmed, and the last time the minute minder was used was for 5 minutes, 00 will appear in the display when you switch on the Timer; when you then touch + or -, the display will change to 05. You can still select any time you want, even if you have adjusted the timer default setting. The time then counts down in minutes. The time remaining can be seen in the Timer/Memory display and changed at any time by touching - or +. If you want to set another cooking zone to switch off automatically, follow the same steps as described above. 27 Timer and Memory function Memory function The settings used on a particular cooking zone from switching on right through to switching off can be recorded as a Memory programme. Up to 5 of your favourite cooking processes can be saved as Memory programmes. Programme slots that have settings memorised to them are indicated by a dot after the number, for example: P 1 Nothing saved in memory P 1. If all programme slots are occupied and you want to save a new cooking process, you will first have to delete one of the existing programmes. Recording a Memory programme The maximum time that can be recorded is 99 minutes with a maximum of 10 changes in power level. ^ Touch the + sensor until the programme number you require shows in the display. During recording, the indicator lamp for the cooking zone being used flashes in the Timer/Memory display, and the programme number lights up. [. . . ] Remember to maintain a minimum safety distance of 50 mm from the back wall, as well as from any tall unit or side wall to the right or left of the hob. ^ Seal the cut surfaces with a suitable heat-resistant sealant to avoid swelling caused by moisture. If, during installation, you find that the seals on the corners of the frame are not flush with the worktop, the corner radius ß R4, can be carefully scribed to suit. These hobs have a seal underneath them to keep the hob securely in position. [. . . ]