User manual MIELE G 2183SCVI FULLY-INTEG RATED, FULLSIZE DISHWASHER OPERATING AND INSTALLATION MANUAL

[. . . ] Operating Instructions Dishwasher G 2183 To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M. -Nr. 54 3 IMPORTANT SAFETY INSTRUCTIONS WARNING ­ When using your dishwasher, follow basic precautions, including the following: Electrical Safety ~ Before installation, make sure that Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. Keep these operating instructions in a safe place and pass them on to any future user. the voltage and frequency listed on the data plate correspond with the household electrical supply. disconnect the power supply to the work area by unplugging the unit, "tripping" the circuit breaker or removing the fuse. [. . . ] Also make certain your china and crystal are dishwasher safe. 25 Use Adding detergent ^ To open, press the latch on the detergent dispenser. The flap is always open at the end of a program. ^ Use one tab or add powder or gel detergent to compartment II and close the flap. ^ If a Pre-rinse is desired, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I. The horizontal marks in compartment II indicate the levels of approximately 1 ¼ and 2 tablespoons (20 and 30 ml) respectively. Compartment I holds a maximum of 2 teaspoons (10 ml). 26 Use Turning on ^ Open the water supply, if closed. The "g" indicator lights up. Selecting and starting a program Choose your program according to the type of load and soiling. Otherwise important program steps may be interrupted. 27 Program guide Program When to use Prerinse 1 2 Program sequence Main wash Interim rinse 1 2 Final rinse Drying Pots & Pans For normally soiled pots and pans with dried on food, also for heavily soiled dishware, use 120% of normal detergent amount For normally soiled dishware For temperature sensitive glassware and lightly soiled dishware, use 50 % of normal detergent amount Extended wash time, for sanitizing normally soiled dishware with dried on food "Quick program" for lightly soiled dishware, e. g. party dishware includes sensor controlled Glasscare, not suitable for detergent tabs To rinse dishes when a complete program is not needed detergent is not recommended x x x x x Normal China & Crystal SaniWash x x x x x x x x x x x x x Express x x x x Rinse & Hold x Usage: Electric: 0. 01 - 1. 23 kWh Water: 1. 3 - 5. 0 gal (5 - 19 l) 28 Use At the end of a program ^ Open the door a few inches to see if the program has finished. Unloading the lower basket first will prevent water drops from the upper basket and cutlery tray (depending on model) from dropping onto dishes in the lower basket. The dishwasher continues to use electricity until turned off with the "o" button. Interrupting a program A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted. , Open the door with care. Close the door firmly until it clicks into place. Changing a program If the detergent flap is already open, do not change the program. If a program has already started and you wish to change it: ^ Open the door. ^ Start the program by closing the door. Preparing your appliance for an extended vacaion If you elect to turn off the water to your home for an extended period of time, please note that this may not be enough to reduce the risk of a leak. To be completely safe, you must turn off the water supply to each individual appliance. This means under the sink for a dishwasher, at the laundry bib for your washer, etc. 29 Additional options Buzzer A signal sounds at the end of a program and when a fault occurs. The buzzer at the end of a program sounds five times in quick succession for up to one hour. ^ Press the "Program" button and at the same time turn the dishwasher on with "g". ^ Hold the program button until the "Rinse & Hold" program indicator comes on. The "Intake / Drain" indicator flashes four times in intervals. The setting can be recognized by the flashing of the "SaniWash" indicator: ­ flashing: buzzer is activated ­ not lit up: buzzer is deactivated ^ To change the setting press the "Program" button for at least one second, until the "Intake / Drain" indicator lights up. ^ Turn the dishwasher off "o". 30 Additional options Default settings All settings can be reset to the factory default. [. . . ] A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for the electrical current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. , Improper connection of the equipment grounding conductor can result in electric shock. [. . . ]