User manual MIELE G 2143SC PREFINISHED, FULLSIZE DISHWASHER OPERATING AND INSTALLATION MANUAL

[. . . ] Operating Instructions Dishwasher G 2143 To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M. -Nr. 56 3 IMPORTANT SAFETY INSTRUCTIONS WARNING ­ When using your dishwasher, follow basic precautions, including the following: Electrical Safety ~ Before installation, make sure that Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. Keep these operating instructions in a safe place and pass them on to any future user. the voltage and frequency listed on the data plate correspond with the household electrical supply. disconnect the power supply to the work area by unplugging the unit, "tripping" the circuit breaker or removing the fuse. [. . . ] The horizontal marks in compartment II indicate the levels of approximately 1 ¼ and 2 tablespoons (20 and 30 ml) respectively. Compartment I holds a maximum of 2 teaspoons (10 ml). 26 Use Turning on ^ Open the water supply, if closed. The "Start / Stop" indicator flashes and the indicator next to the last program selected is lit. Selecting and starting a program Choose your program according to the type of load and soiling. The indicators for "Start / Stop", "Rinse" and the program selected will light up. If the function "Turbo" is selected, the relevant indicator will also light up. Otherwise important program steps may be interrupted. Program sequence display After a program has been started the current stage of the program is indicated by the program sequence indicator. 27 Program guide Program When to use Prerinse 1 2 Program sequence Main wash Interim rinse 1 2 Final rinse Drying Pots & Pans For normally soiled pots and pans with dried on food, also for heavily soiled dishware, use 120% of normal detergent amount For normally soiled dishware For temperature sensitive glassware and lightly soiled dishware, use 50 % of normal detergent amount Extended wash time, for sanitizing normally soiled dishware with dried on food "Quick program" for lightly soiled dishware, e. g. party dishware includes sensor controlled Glasscare, not suitable for detergent tabs To rinse dishes when a complete program is not needed detergent is not recommended x x x x x Normal China & Crystal SaniWash x x x x x x x x x x x x x Express x x x x Rinse & Hold x Usage: Electric: 0. 01 - 1. 23 kWh Water: 1. 3 - 5. 0 gal (5 - 19 l) 28 Use At the end of a program When the program has finished the "End" indicator lights. Unloading the lower basket first will prevent water drops from the upper basket and cutlery tray (depending on model) from dropping onto dishes in the lower basket. The dishwasher continues to use electricity until turned off with the "K" button. Preparing your appliance for an extended vacaion If you elect to turn off the water to your home for an extended period of time, please note that this may not be enough to reduce the risk of a leak. To be completely safe, you must turn off the water supply to each individual appliance. This means under the sink for a dishwasher, at the laundry bib for your washer, etc. 29 Use Interrupting a program A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted. Changing a program If the detergent flap is already open, do not change the program. If a program has already started and you wish to change it: ^ Press and hold the "Start / Stop" button for at least one second. The program is canceled and "Start / Stop" flashes in the display. ^ Select the desired program and start as usual. , Open the door with care. Close the door firmly until it clicks into place. 30 Additional options Turbo The "Turbo" function can be used to reduce the program run-times, in programs in which the option is available. The option will remain active for all programs until the setting is changed again. ^ A program can now be started as usual or the dishwasher can be turned off "K". Default settings All settings can be reset to the factory default. ^ Press and hold the "Start / Stop" button and at the same time turn the dishwasher on "K". Hold the "Start / Stop" button until the indicator lights up. The "Rinse & Hold" indicator gives one long flash and two short flashes in intervals. The "Rinse" indicator lights up showing that a setting other than the factory default has been set. [. . . ] A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for the electrical current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. , Improper connection of the equipment grounding conductor can result in electric shock. [. . . ]