User manual MIELE G 879 SCVI

[. . . ] Operating and installation instructions Dishwasher G 879 SCVi In order to protect yourself and avoid damage to your machine, it is absolutely necessary to read the operating and installation instructions prior to installation and operation. ] M. -Nr. 32 33 33 34 34 34 35 35 35 36 36 38 39 40 41 41 41 41 42 44 45 46 49 67 68 73 3 Guide to the appliance Guide to the appliance View of the machine Control panel (12) 4 Guide to the appliance 1 Upper spray arm (not visible) 2 Cutlery tray 3 Upper basket 4 Water guide duct for middle spray arm 5 Middle spray arm 6 Water hardness selector 7 Lower spray arm 8 Four height adjustable levelling legs 9 Combination filter 10 Salt reservoir 11 Dual compartment detergent dispenser 12 Control panel 13 Rinse aid reservoir (with dosage selector) 14 Adhesive label with programme names 15 Data plate 16 Indicator lamps 17 programme touch pads 18 Top Solo touch pad 19 O - OFF touch pad 20 I - ON touch pad o Programme label An adhesive label listing the programme names is supplied with the dishwasher. It should be placed in the indented area next to the programme touch pads. Remove the backing from the label and place it into the indented area. [. . . ] Press and hold buttons b and d while simultaneously turning on the dishwasher. The "ON" indicator lamp will light and the "8 k" and c lamps will flash. If any other indicator lamps flash, turn off the dishwasher and start again. The "8 k" indicator lamp will flash as long as you are in the programming mode. If the b lamp lights up, "Heated drying" is already turned off. If the lamp is not lit, proceed as follows: Turning on "Heated drying". In order to turn "Heated drying" back on, follow the same procedure, making sure the b indicator lamp is off before storing the change using the 2 button. Its indicator lamp will light up and indicator lamps b through f will go out (if previously lit). The change has been stored and "Heated drying" is now turned off for all wash programmes. 34 Additional features End of programme notification A buzzer will sound to indicate the end of the wash programme. Press and hold buttons b and d while simultaneously turning on the dishwasher. The "ON" indicator lamp will light and the "8 k" and c lamps will flash. If any other indicator lamps flash, turn off the dishwasher and start again. The "8 k " indicator lamp will flash as long as you are in the programming mode. Its indicator lamp will light up and indicator lamps e through c will go out (if previously lit). The change is now stored and the buzzer is turned off for all wash programmes. In order to turn the buzzer back on, follow the same procedure, making sure the indicator lamp is off before storing the change using the 2 button. 35 Cleaning and care Cleaning and care Cleaning the filters in the wash cabinet. The combination filter in the base of the wash cabinet should be regularly inspected and cleaned as necessary. Any broken glass or dishware should be removed immediately upon discovery. Use caution when cleaning the filters, non-return valve or drain pump, as glass or bone splinters may be caught in the bottom of the wash cabinet. Turn the handle counterclockwise to release the filters. Lift the combination filter out of the machine. A nylon brush can be used, if necessary. 36 Cleaning and care Turn the combination filter over and open the coarse filter cover by pulling back on the locking tab. Clean as for the combination filter, and press the locking device back in. Important: After cleaning, make sure that the locking device is properly locked. Replace the combination filter so that it lies flat in the base of the wash cabinet. Secure it by turning the handle clockwise. 37 Cleaning and care Cleaning the spray arms On rare occasions particles of food may get stuck in the spray arm jets. [. . . ] In order for this feature to be active, the machine must be "ON" (not necessarily running) and the door must be closed when the dishwasher is not being used. Water connection Note: Water connections must be in accordance with national and local codes ordinances. Connection to the water inlet The dishwasher should be connected to hot water (max. NB Please check with the Miele Service Department if you are unsure whether your household hot water system is suitable. A shut-off valve with 3/4" male thread must be provided on site (garden hose type, 11. 5 threads per 1" length). If the water pressure is too low the machine may not take in enough water in the allowed time and the "Water Intake" indicator lamp will flash (see "Problem solving guide"). [. . . ]