User manual MIELE EGW 4060-14 PLATE & CUP WARMER OPERATING AND INSTALLATION MANUAL

[. . . ] If there is any doubt, have the electrical system of the house checked by a qualified electrician. The manufacturer cannot be held responsible for the damages caused by an inadequate grounding system (e. g. Do not connect the appliance to the electrical supply with an extension cord. Extension cords do not guarantee the required safety of the appliance. [. . . ] Pull the drawer out all the way when removing dishes to avoid touching hot drawer parts. Supervise its use by the elderly or infirm. 5 Guide to the machine a On/Off button b Temperature selector c Warming drawer d Non-slip mat e Indicator 6 Before using the plate warmer ^ Clean the plate warmer with a damp cloth and wipe dry. Turn the temperature selector to "Maximum" (see "Selecting a temperature"). Metal components have a protective coating which may give off a slight odor the first time your new appliance is heated. The smell will dissipate after a short time and does not indicate a faulty connection. 7 Use Controls The plate warmer is only intended for warming dishes. Do not use the plate warmer to reheat, cook or keep food and drinks warm. Condensation from food and drinks may cause moisture damage to the appliance. The floor of the warming drawer has a non-slip mat to prevent plates and dishes from sliding when the drawer is opened and closed. The controls consist of the temperature selector and the On/Off button. The indicator on the front of the drawer show if the plate warmer is turned on or off. 8 Use Operating ^ Place the dishes in the drawer. Do not turn the knob counterclockwise or clockwise past the 9 o'clock position. Forcing it beyond these positions will damage the temperature selector. When the selected temperature is reached, the heating element turns off. If the temperature falls below the selected one, the heating element will turn on again. The temperature scale shows symbols for the optimum temperature of the respective dish group: ­ b approx. When served in a prewarmed cup, glass or plate, the drink or food will not cool as fast and the cup or plate will remain cool enough to touch. Selecting a temperature The temperature selector allows you to select a temperature between 86° and 176 °F (30 and 80 °C). 9 Use Warming times Various factors will affect the warming times: ­ type and thickness of dishes, ­ quantity, ­ how dishes are arranged, and the ­ temperature setting. As you use the plate warmer you will learn which settings suit your needs best. At a temperature setting of r, (about 140 °F (60 °C)), place settings for 6 people, will be evenly warmed in approximately 30 to 35 minutes. Capacity The capacity of the appliance depends on the dish sizes. The following assembly picture is an example. ­ Place settings for 6 people: 6 plates diam. 6 11/16" (17 cm) 2 serving plates 14 3/16" (36 cm) not pictured ­ 80 Espresso cups, or ­ 40 Cappuccino cups 10 Cleaning and care Cleaning the plate warmer Let the drawer cool before cleaning. Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the plate warmer. The exterior of the plate warmer can be cleaned with warm water and liquid dish soap applied with a soft sponge. [. . . ] ^ Install the combination appliance according to the manual supplied with that machine. 20 Installation Aligning the appliance front After installing the combination appliance it might be necessary to align the appliance front and/or to even the gap between the plate warmer and the combination machine. Flat washers are supplied beneath the knurled nuts, which fix the drawer to the telescopic runners. ^ Loosen the knurled nuts and take the drawer out. ^ Align and even the gap with the flat washers by changing their position (above or below the drawer), on both sides. 21 Installation Electrical connection The electrical installation instructions for any appliance installed in combination with the plate warmer must be observed. When another appliance is installed in combination with the plate warmer to the same circuit breaker, operating both appliances at the same time may cause an overload. [. . . ]