User manual MIELE EGW 602-14
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MIELE EGW 602-14. We hope that this MIELE EGW 602-14 user guide will be useful to you.
You may also download the following manuals related to this product:
MIELE EGW 602-14 (327 ko)
MIELE EGW 602-14 ANNEXE 494 (355 ko)
Manual abstract: user guide MIELE EGW 602-14
Detailed instructions for use are in the User's Guide.
[. . . ] Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. The electrical safety of this appliance can only be guaranteed when continuity exists between the appliance and an effective grounding system, which complies with local and national safety regulations. It is imperative that this basic safety requirement is tested by a qualified electrician. The manufacturer cannot be held responsible for the consequences of an inadequate grounding system (e. g. [. . . ] Children climbing on the appliance to reach these items could be seriously injured. Loose-fitting or hanging garments should never be worn while using the plate warmer. Moist or damp pot holders used on hot surfaces may result in steam burns. Due to the high temperatures radiated, objects left near the appliance could catch fire. The steam could penetrate electrical components and cause a short circuit. In areas subject to infestation by cockroaches or other vermin, keep the appliance and its surroundings clean at all times. Any damage caused by pests will not be covered by the appliance warranty. Do not use outdoors.
Disposal of an old appliance
Before discarding an old appliance, disconnect the power cord and remove any doors to prevent hazards.
7
Using the plate warmer
The plate warmer is only intended for warming dishes. Do not use the plate warmer to re-heat, cook or keep food or drinks warm. Condensation from food or drinks could cause moisture damage to the appliance. A protective grill prevents any contact with the heating element and fan. The rail in the drawer separates the control panel, heating element and fan from the rest of the drawer. This prevents plates from being placed too close to the control panel and being damaged when the drawer is pushed in. The floor of the warming drawer has a non-slip mat to prevent plates and dishes sliding when the drawer is opened and closed.
Controls
The controls consist of the temperature selector knob and the On/Off button. These are only visible when the drawer is open.
8
Using the plate warmer
Warming dishes
Procedure in brief: ^ Place the dishes in the warming drawer. The indicator on the front of the appliance lights up to show that the appliance is on. The following loading examples are given as a guide only.
Loading the drawer
The quantity which can be loaded will depend on the type and size of your dishes. When the drawer is closed, these will block the vents for the heated air and prevent the dishes from warming evenly.
6 place settings: 6 dinner plates (11"/28 cm) 6 dessert bowl 3 serving bowls 2 plates (14 "/ 36 cm) or one of the following: 20 dinner plates (11"/28 cm) 36 soup bowls (8"/22 cm) 30 dessert bowls 10 dinner plates (11"/28 cm) 10 soup bowls (8"/22 cm) 80 espresso cups 40 cappuccino cups 30 punch glasses 18 soup bowls (8"/22 cm) 2 soup tureens (8" x 7"/ 21 cm x 18 cm)
9
Using the plate warmer
Selecting a temperature The temperature control is used to adjust the temperature setting. The heat will shut off automatically when the selected temperature is reached. It will turn back on again as soon as the temperature drops below the selected temperature. A temperature range between approximately 86 °F and 176°F (30 °C and 80 °C) can be set. Recommended temperatures for pre-heating: approximately 104 °F (40 °C) b for cups and glasses. [. . . ] When installed in combination with another appliance, the plate warmer must always be installed beneath the other appliance. ^ Push the appliance into the cabinetry and align it.
^ Open the plate warmer drawer and use two screws to secure the plate warmer to the side walls of the cabinetry.
16
Installing the plate warmer
Adhering the insulation strips
Aligning the front of the plate warmer After installing the combination appliance, it may be necessary under certain circumstances to align the front of the plate warmer. align the gap between the plate warmer and the combination appliance. To help you do this, there are adjusting points underneath the nuts which secure the drawer to the telescopic runners.
^ Remove the protective foil from the adhesive strips. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MIELE EGW 602-14
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MIELE EGW 602-14 will begin.