User manual MIELE EGW 601-14

[. . . ] This appliance must only be used once it has been installed in cabinetry to ensure that all electrical components are shielded. Tampering with electrical connections or components and mechanical parts is dangerous and can cause machine damage. 3 IMPORTANT SAFETY INSTRUCTIONS Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return the appliance to the nearest authorized service facility for service. Installation, repair and maintenance work should be by a Miele authorized service technician. [. . . ] The steam could penetrate electrical components and cause a short circuit. In areas subject to infestation by cockroaches or other vermin, keep the appliance and its surroundings clean at all times. Any damage caused by pests will not be covered by the appliance warranty. Do not use outdoors. Disposal of an old appliance Before discarding an old appliance, disconnect the power cord and remove any doors to prevent hazards. 5 Help protect our environment Disposal of the packing material The transport and protective packing materials are environmentally friendly for disposal and may be recyclable. Ensure that any plastic wrap is disposed of safely and kept out of the reach of babies and young children. Please recycle. Disposal of an old appliance Old appliances contain materials which can be recycled. Ensure that the appliance presents no danger to children while waiting for disposal. See the instructions in the "Important Safety instructions". 6 Guide to the plate warmer a On/Off button b Temperature control c Warming drawer d Non-slip mat e Rail f On/Off indicator light 7 Using the plate warmer The plate warmer is only intended for warming dishes. Do not use the plate warmer to re-heat, cook or keep food or drinks warm. Condensation from food or drinks could cause moisture damage to the appliance. A protective grill prevents any contact with the heating element and fan. The rail in the drawer separates the control panel, heating element and fan from the rest of the drawer. This prevents plates from being placed too close to the control panel and being damaged when the drawer is pushed in. The floor of the warming drawer has a non-slip mat to prevent plates and dishes sliding when the drawer is opened and closed. The controls consist of the temperature selector knob and the On/Off button. These are only visible when the drawer is open. Controls 8 Using the plate warmer Warming dishes Procedure in brief: ^ Place the dishes in the warming drawer. The indicator on the front of the appliance lights up to show that the appliance is on. The following loading examples are given as a guide only. Loading the drawer The quantity which can be loaded will depend on the type and size of your dishes. When the drawer is closed, these will block the vents for the heated air and prevent the dishes from warming evenly. 6 place settings: 6 dinner plates (11"/28 cm) 6 dessert bowls 3 serving bowls 2 plates (14 "/ 36 cm) or one of the following: ­ 20 dinner plates (11"/28 cm) ­ 36 soup bowls (8"/22 cm) ­ 30 dessert bowls ­ 10 dinner plates (11"/28 cm) 10 soup bowls (8"/22 cm) ­ 80 espresso cups ­ 40 cappuccino cups ­ 30 punch glasses ­ 18 soup bowls (8"/22 cm) 2 soup tureens (8" x 7"/ 21 cm x 18 cm) 9 Using the plate warmer Selecting a temperature The temperature control is used to adjust the temperature setting. The heat will shut off automatically when the selected temperature is reached. It will turn back on again as soon as the temperature drops below the selected temperature. A temperature range between approximately 86 °F and 176°F (30 °C and 80 °C) can be set. [. . . ] When installed in combination with another appliance, the plate warmer must always be installed beneath the other appliance. ^ Push the appliance into the cabinetry and align it. ^ Open the plate warmer drawer and use two screws to secure the plate warmer to the side walls of the cabinetry. 16 Installing the plate warmer Adhering the insulation strips Aligning the front of the plate warmer After installing the combination appliance, it may be necessary under certain circumstances to: a b b a ­ align the front of the plate warmer. ­ align the gap between the plate warmer and the combination appliance. To help you do this, there are adjusting points underneath the nuts which secure the drawer to the telescopic runners. ^ Remove the protective foil from the adhesive strips. [. . . ]