User manual MIELE DG 155 CONVECTION STEAM OVEN INSTALLATION MANUAL

[. . . ] The steam oven should be installed at a safe height for users to safely access all cooking levels and containers. This equipment is not designed for maritime use or for use in mobile installations such as caravans or aircraft. However, under certain conditions it may be possible for an installation in these applications. [. . . ] Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. Installation, repair and maintenance work should be by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. Before installation or service, disconnect the power supply to the work area by removing the fuse, "tripping" the circuit breaker, or switching off the power main. Ensure that the power is not restored to the appliance during maintenance or repair work. Do not use an extension cord to connect this appliance to electricity. Extension cords do not guarantee the required safety of the appliance, (e. g. Do not operate any appliance with a damaged cord or plug or after the appliance has been damaged in any manner. Return the appliance to the nearest authorized service facility for examination, repair or adjustment. IMPORTANT SAFETY INSTRUCTIONS Disposal of an old appliance Before discarding an old appliance, disconnect it from the electricity supply, cut off the power cord and remove any doors to prevent hazards. Note to the installer: Please leave these instructions with the consumer of the appliance. Important Save these instructions for the local electrical inspector's use 4 Appliance and cut out dimensions Installation in tall cabinetry e d 78 15 3 (10 16 " m) 0m f 221 16 " (560-5 22 3 8 " 68mm ) ( m 22m ) 17 1516" (456mm) 23 7 16 " (59 5m m) b a Steam oven b Cabinet opening c Terminal block d Outlet or junction box. e Power supply cord 17 8" (447mm) c 5 17 11 16" (450mm) " 13" ) mm (330 21 9 16 " (547 mm) 13" . 3 (min 30) 5 Appliance and cut out dimensions Installation under a counter top e 78 " m (22 (m 17 1516" (456mm) 17 8" (447mm) (560 221 16 " -568 - 22 3 8 mm) " c 23 7 16 " (59 5m m) b a Steam oven b Cabinet opening c Terminal block d Outlet or junction box. e Power supply cord 6 5 17 11 16" (450mm) m) 13" m) 30m (3 d 21 9 16 " (547 mm) f 14 9 16 " ) 70 in. 3 Appliance and cut out dimensions Installation above a Miele oven 78 " 13" ) (330m m) d21 e 9 16 15 " 3 16 " ( m 22m (547m m) f 17 8" (447mm) 17 11 16" (450mm) m) 0m (10 17 1516" (456mm) (mi 13" 30) . 3 n (560 c - 22 3 8 mm) 221 16 " 5 b (596mm) 16" -568 " 237 1 6 " 219 16 " 23 13 " 22 16 (580mm) (56 221 16 0-5 "- 2 g 23 7 (59 16 " 5m m) 78 " (22 ) mm 21 m) 0m (55 58 " a Steam oven b Cabinet opening c Terminal block d Outlet or junction box. e Power supply cord g Oven Note: The steam oven must not rest directly on top of the oven. The steam oven should be supported by a shelf or ledges. 23 68m m) 3 8 2 3 8" (593-595mm) (56 0 " - 23 716 22 m) m 1 16 " c 7 7 Installing the oven Securing the oven After aligning the oven it must be secured in position. [. . . ] For CDN only The appliance is provided with 3 terminal leads: 1 black wire (L1), 1 red wire (L 2) and 1 green wire (GND) that must be connected to a dedicated junction box. Connect the black wire to L1, the red wire to L2 and the green wire to GND. All hot wires (black and red) must be fused individually before connecting them to the main power supply leads. [. . . ]