User manual MIELE DA 62 VENTILATION HOOD OPERATING MANUAL

[. . . ] appliance, switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. If the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system. If there is any doubt, have the electrical system of the house checked by a qualified electrician. ~ b) Before servicing or cleaning the ~ This appliance is intended for ~ This appliance complies with current safety requirements. [. . . ] ^ To activate the automatic switch back, press the "+" button. ^ To save the setting, press the "Delayed shut down" button "5 ¢15". If the procedure is not stored within 4 minutes, the hood will automatically default to the "old" data. Selecting the power level - / + ^ Press the "­" symbol to select a lower power level or the "+" symbol for a higher power level. Depending on the amount of cooking odors, levels 1 to 3 are usually sufficient for normal cooking. Intensive setting "IS" To remove strong aromas or odors, for example when frying, select power level IS temporarily. 10 Operation Delayed Shut Down 5 ¢15 For both air extraction and recirculation, it is recommended that run the fan for several minutes after cooking is completed. The Delayed Shut Down feature can be selected to turn the fan off automatically after a preselected length of time. ^ After cooking, and with the fan on, press the Delayed Shut Down button 5 ¢15 ­ ­ once: the fan automatically switches off after 5 minutes (5 ¢ lights up). ­ twice: the fan automatically switches off after 15 minutes (¢15 lights up). If you press the Delayed Shut Down button 5 ¢15 again, the fan will not turn off automatically (5 ¢15 goes out). Overhead lighting I Turning the overhead lighting on The overhead lighting can be turned on and off independently of the fan. Dimming the overhead lighting The brightness of the lighting can be adjusted. ^ If the button I is pressed and held down again, the lighting will brighten until the button is released. Support the grease filter so that it does not fall and damage the cooktop. 15 Cleaning and Care Cleaning the grease filters ^ By hand: use a scrub brush with a solution of warm water and mild dish soap. Do not use the pure detergent, aggressive all purpose cleaners, oven sprays, abrasive cleaning agents or limescale removers. ^ In a dishwasher: place the filter vertically in the lower basket, making sure that the spray arm is not blocked. Depending on the detergent, cleaning the grease filters in a dishwasher may cause permanent discoloration of the filter surface. ^ While the filters are removed, clean any dirt or grease from the filter casing. ^ When putting the grease filters back make sure that the locking clips are visibly facing the cooking surface ^ If the filters are incorrectly installed, insert a small screwdriver into the slit along its edge to disengage it from the casing. Resetting the grease filter timer After cleaning reset the grease filter operating hours timer. ^ With the fan running, press and hold the grease filter button [ for approx. If the grease filters are cleaned before the timer has reached its maximum: Press and hold the grease filter button [ for about 6 seconds, until only the 1 is flashing 16 Cleaning and Care Changing the light bulbs , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before changing the light bulbs, disconnect the hood from the power supply, see "Important Safety Instructions". When in use halogen bulbs become extremely hot, and can burn your hands. Do not attempt to change the bulbs until they have had sufficient time to cool. ^ Using a cloth or glove, insert the new halogen bulb (type 12 V, 20 W, G4). [. . . ] ­ To ensure free access to work under the ventilation hood, a distance of a minimum of 26" (660 mm) above the electric cooktop is also recommended. 22 Structural support The ceiling mounting plate will support the weight of the hood. This ceiling plate must be attached to rigid structural framing that is supported in its entirety by the ceiling joists, or to the ceiling joists directly. Do not attach the plate directly to the ceiling with anchors, toggle bolts, etc. , CAUTION When cutting or drilling into the wall or ceiling, do not damage electrical wiring and other hidden utilities. 23 Installation Before installation read the information in the "Appliance Dimensions" and " Important Safety Instruction" chapters. Under certain conditions, there is a danger of poisonous fumes by when the ventilation system and a furnace drawing interior air run at the same time. 4 levelling plates for correcting an uneven ceiling. Installation instructions The individual installation steps are described in the included Installation diagram. [. . . ]