User manual MIELE DA 5000 D

[. . . ] Operating and Installation Instructions Ventilation System DA 5000 D To prevent accidents and appliance damage, read these instructions before installation or use. en - US, CA M. -Nr. 31 2 IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Keep these instructions in a safe place and pass them on to any future user. Read these instructions carefully before installing or using the Ventilation System. Use the appliance only for its intended purpose. , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: ~ a) Use this appliance only in the manner intended by the manufacturer. [. . . ] ­ A time of 20 hours should also be programmed if the kitchen is only used occasionally. This will help to prevent grease which has accumulated over a long period of time from hardening on the filters making cleaning more difficult. ­ If you typically use very little fat for cooking, an interval of 40 or 50 hours can be selected. To reprogram the timer: ^ Touch the "s" sensor button to turn off the fan. ^ Touch the sensor buttons "5m15" and "l" at the same time. The sensor button "l" and one of the sensor buttons "1" to "4" will flash. The sensor buttons "1" to "4" show the amount of time set: Sensor button "1" = 20 hours Sensor button "2" = 30 hours Sensor button "3" = 40 hours Sensor button "4" = 50 hours ^ To select a shorter time, touch the sensor button "1". If the procedure is not confirmed within 4 minutes of programming, the hood will automatically default to the "old" setting. Sensor button tone Whenever you select a feature with the sensor buttons, a brief tone is heard. ^ Simultaneously, press and hold the sensor buttons "4" and "l" for approx. If the exhaust hood is disconnected from the power supply, or after a power interruption, the tone is automatically re-activated, regardless of the previous settings. 13 Cleaning and care , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before cleaning or servicing the hood, disconnect it from the power supply, see "Important Safety Instructions". Cleaning the casing Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the hood. ^ All external surfaces and controls can be cleaned with a mild solution of warm water and liquid dish soap applied with a soft sponge. Avoid: ­ cleaning agents containing soda, acids or chlorides, ­ abrasive cleaning agents, e. g. pot scourers or sponges which have been previously used with abrasive cleaning agents. The following instructions for cleaning "Stainless steel" surfaces should be followed in addition to the general "Cleaning the casing" instructions. Stainless steel Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner. To help prevent resoiling, a conditioner for stainless steel can be applied. Glass surfaces Glass surfaces can be cleaned using a glass cleaner. 14 Cleaning and care Grease filters The reusable metal grease filters remove solid particles from the vented kitchen air (grease, dust, etc) and help keep the exhaust hood clean. At the latest, clean the grease filter when the "l" sensor button lights up. The grease filters should be cleaned every 3 - 4 weeks or when the grease filter indicator lights. Be sure to support the grease filter so that it does not fall onto the cooktop. , A dirty filter is a fire hazard. To remove the grease filters, first open the canopy. The canopy remains open. ^ Press slightly upward on the grease filter handle to release it from the lower rail, pivot forward and lower it downward. [. . . ] ­ If there is more than one appliance beneath the hood and they have different minimum safety distances always select the greater distance. See "Important Safety Instructions" for further information. 25 Structural support The ceiling mounting plate will support the weight of the hood. This ceiling plate must be attached to rigid structural framing that is supported in its entirety by the ceiling joists, or to the ceiling joists directly. Do not attach the plate directly to the ceiling with anchors, toggle bolts, etc. , CAUTION When cutting or drilling into the wall or ceiling, do not damage electrical wiring and other hidden utilities. 26 Installation Protective film The casing is covered with a protective film to prevent scratching during transport. [. . . ]