User manual MIELE DA 289 DESIGNER WALL HOOD OPERATING AND INSTALLATION MANUAL

[. . . ] Operating and Installation Instructions Ventilation System DA 289-4 To prevent accidents and appliance damage, read these instructions before installation or use. en - US M. -Nr. 07 782 280 Contents IMPORTANT SAFETY INSTRUCTIONS Functional description Guide to the Ventilation System Operation Turning on the fan . 19 After Sales Service Installation instructions Caring for the environment Appliance dimensions Installation accessories Plywood backing Installation Dismantling . 29 Air extraction Electrical connection 2 IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Keep these instructions in a safe place and pass them on to any future user. [. . . ] Stainless steel Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner. To help prevent resoiling, a conditioner for stainless steel can also be used. Stainless steel colored controls These controls may become discolored or damaged if not cleaned regularly. Do not use a stainless steel cleaner on these controls. , Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the hood. They will damage the surface. ^ The air intake panel, exterior surfaces and controls can be cleaned with a mild solution of warm water and liquid dish soap applied with a soft sponge. ^ Glass surfaces can be cleaned using glass cleaner. 16 Cleaning and care Grease filter and air intake panel The reusable metal grease filter removes solid particles from the vented kitchen air (grease, dust, etc). Removing the air intake panel The grease filter and the air intake panel should be cleaned every 3 - 4 weeks or whenever the grease filter indicator lights. , A dirty filter is a fire hazard. ^ To remove the air intake panel gently pull out and downward, shifting the lower part a bit to the right. Support the air intake panel so that it does not fall onto the cooktop. Removing the grease filter ^ To remove the grease filter, pull on the lever. Support the grease filter so that it does not fall onto the cooktop. 17 Cleaning and care Cleaning the grease filters ^ By hand: use a scrub brush with a solution of warm water and mild detergent. Do not use the pure detergent, aggressive all purpose cleaners, oven sprays or limescale removers. ^ In a dishwasher: place the filters vertically in the lower basket, making sure that the spray arm is not blocked. Depending on the detergent, cleaning the grease filter in a dishwasher may cause permanent discoloration of the filter surface. ^ Clean the air intake panel according to "Cleaning the casing". ^ While the filter and the air intake panel are removed, clean any dirt or grease from the interior casing to prevent the risk of fire. ^ Push the grease filter back in place. ^ Hook the air intake panel on the latches and push a little to the left. ^ After returning the grease filter, press the grease filter button for 3 seconds to reset the timer. ^ If the grease filter and air intake panel are cleaned before the grease filter timer has reached its maximum, the grease filter button should be pressed for 6 seconds to reset the counter to zero. 18 Cleaning and care Changing the light bulb , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before changing the light bulbs, disconnect the hood from the power supply, see "Important Safety Instructions". Replacement bulbs may be ordered from Miele's Technical Service Department. See the phone numbers on the back of this booklet. When in use halogen bulbs become extremely hot, use caution. Do not attempt to change the bulbs until they have had sufficient time to cool. Fingerprints or body oils deposited on the bulb will decrease its life. [. . . ] Please read and follow the "IMPORTANT SAFETY INSTRUCTIONS" to reduce the risk of personal injury. Exhaust ducting and connections Use smooth or flexible pipework made from approved non-flammable materials for exhaust ducting. To achieve the most efficient air extraction and quietest noise levels, consider the following: ­ The diameter of the ductwork should not be less than 6" (150 mm). ­ If flat ducting is used, the cross section must not be smaller than the cross section of the ventilation exhaust. [. . . ]