User manual MIELE DA 249 DESIGNER WALL HOOD OPERATING MANUAL

[. . . ] Operating and Installation Instructions Ventilation System DA 249-4 To prevent accidents and appliance damage, read these instructions before installation or use. en - US, CA M. -Nr. 38 2 IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Keep these instructions in a safe place and pass them on to any future user. Read these instructions carefully before installing or using the Ventilation System. Use the appliance only for its intended purpose. , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: ~ a) Use this appliance only in the manner intended by the manufacturer. [. . . ] The following instructions for cleaning "Stainless steel" surfaces and "Stainless steel colored controls" should be followed in addition to the general "Cleaning the casing" instructions. Stainless steel Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner. To help prevent resoiling, a conditioner for stainless steel can also be used. Stainless steel colored controls These controls may become discolored or damaged if not cleaned regularly. Do not use a stainless steel cleaner on these controls. 17 Cleaning and Care Grease filter The decor panel and reusable metal grease filter remove solid particles from the vented kitchen air (grease, dust, etc). Removing the decor cover The grease filters should be cleaned every 3 - 4 weeks, when the grease filter indicator lights, or when they are visibly dirty, whichever comes first. Always clean both the decor panel and the grease filter. ^ To remove the decor cover, pull on the release knobs. Hold the decor cover when doing this so that it does not fall on to the cooktop. Removing the grease filter , A dirty filter is a fire hazard. ^ To remove the grease filter, pull on the release knob. Hold the grease filter when doing this so that it does not fall on to the cooktop. 18 Cleaning and Care Cleaning the grease filters ^ By hand: use a scrub brush with a solution of warm water and mild detergent. Do not use the pure detergent, aggressive all purpose cleaners, oven sprays or limescale removers. ^ In a dishwasher: place the filters vertically in the lower basket, making sure that the spray arm is not blocked. Depending on the detergent, cleaning the grease filter in a dishwasher may cause permanent discoloration of the filter surface. ^ While the filter is removed, clean any dirt or grease from the filter casing to prevent the risk of fire. ^ If the grease filter is cleaned before the timer has reached its maximum, the grease filter button should be pressed for 6 seconds to reset the counter to zero. Inserting the grease filter ^ Angle the grease filter into position toward the front of the hood. ^ Once the front edge of the filter is in place, push up the rear of the filter so that both sides click into place. Inserting the decor cover ^ After returning the grease filter, press the grease filter button for 3 seconds to reset the timer. The indicator light will go out. ^ Hook the decor cover on to the latches on the rear panel of the chimney. Push the cover up at the front so that it clicks in place. 19 Cleaning and Care Active charcoal filters In recirculation mode an active charcoal filter must be used in addition to the grease filter. ^ The decor cover must be removed to access the active charcoal filter. See "Cleaning and Care". ^ To remove the active charcoal filter pull down on the tab at the back of the filter. ^ Before inserting an active charcoal filter for the first time remove the connector for use in air extraction mode. [. . . ] Exhaust ducting and connections Use smooth or flexible pipework made from approved non-flammable materials for exhaust ducting. To achieve the most efficient air extraction and quietest noise levels, consider the following: ­ The diameter of the ductwork should not be less than 6" (150 mm). ­ If flat ducting is used, the cross section must not be smaller than the cross section of the ventilation exhaust. ­ Where the ductwork is horizontal, it must slope away from the hood at least 1/8" per foot (1 cm per meter) to prevent condensation dripping into the appliance. [. . . ]