User manual MIELE DA 8-2 EXTRACTOR

[. . . ] The manufacturer cannot be held responsible for damage caused by the lack or inadequacy of an effective grounding system. Installation and repairs should only be performed by qualified and trained personnel. Do not connect the appliance to the main electrical supply using an extension cord. Extension cords do not guarantee the required safety of the appliance. [. . . ] Ventilation can be maintained by air inlets in windows, doors and outside walls, or by other means, such as ensuring that the extractor can only be turned on when the heating appliance is off and vice-versa. Keep these operating instructions in a safe place for future reference and pass them on to future owners if applicable. 7 Warning and safety instructions Warning and safety instructions Disposal of an old appliance Before disposing of an old appliance, cut the cable off the appliance as close to the housing as possible. The plug and cord should be disposed of and not used elsewhere in the house (electric shock hazard). Text highlighted in boxes is of particular importance, and should be read in conjunction with the warning and safety instructions. 8 Operation Operation Turn the extractor on before starting to cook: Turn the control knob f clockwise. Select a power setting strong enough to clear the air: Setting 1 = for normal operation. After cooking Turn the control knob counter clockwise to "0". 9 Cleaning and care Cleaning and care Before cleaning the extractor disconnect it from the main electrical supply (pull out the plug or trip the circuit breaker). Grease filter A re-usable metal grease filter is used to remove solid particles (oil, dust, etc. ) from kitchen vapors, preventing soiling of the extractor fan. The grease filter should be cleaned regularly to ensure trouble free operation of the extractor fan. Make sure that no particles from the grease filter fall into the interior of the appliance. If this does happen, the Service Department will have to be called to clean the appliance, as the fan casing will need to be dismantled. By hand: in a solution of hot water and detergent using a nylon brush, or In a dishwasher: the grease filter, the ventilation grill and the drip tray should be placed in the bottom basket. When clean and dry, replace the drip tray on the grease filter and re-install it in the appliance. Control panel / Control knob The control panel and control knob should be cleaned in a solution of hot water and detergent and dried using a soft cloth. Do not use abrasive cleaning agents as these will scratch the surface material. To remove the grease filter the ventilation grill (1) must be removed. Carefully withdraw the grease filter (2). 10 After Sales Service After Sales Service In the event of problems you cannot correct yourself, please contact Your Miele Dealer or The Miele Service Department The address of the nearest Service Department is given on the back page. When contacting the Service Department, please quote the Model and Serial No. of the appliance. Space for enclosed data plate 11 Electrical connection Electrical connection Electrical connection - CDN The extractor is supplied with a 1. 10 m power supply cable ready for connection to a 120 VAC, 60 Hz supply. Important The wires of the power cord are colored as follows: Green = ground Black = live White = neutral WARNING THIS APPLIANCE MUST BE GROUNDED Electrical connection - USA The extractor is supplied with a 4 ft cord ready for connection to a 120 VAC, 60 Hz power supply. Fuse rating is 10 A. Important The wires of the power cord are colorcoded as follows: Green/Yellow = ground Blue = neutral Brown = live As the colors of the wires in the power supply cord of this appliance may not correspond with the colors of the wires in your junction box, proceed as follows: The green and yellow wire must be connected to the ground wire. WARNING THIS APPLIANCE MUST BE GROUNDED 12 Appliance dimensions Appliance dimensions 3 3/8" 20 3/16" 14 3/16" 19 5/16" 3 1/16" 13 Installation instructions Installation instructions Do not install the DA 8-2 directly next to a gas hob. [. . . ] When installing more than one combiset, a stainless steel spacer bar must be placed between units. Mount the fan so that the impeller cannot be inadvertently reached by hand. The exhaust ducting should be attached to the exhaust connection using the supplied hose clamp. E 10 1/4" 5 1/2" 17 Exhaust connections Exhaust connections Calculation of exhaust ducting A pipe diameter of 5" should ensure trouble-free extraction up to a total pipe length of 5. 4. Determine the total pipe length as follows: Measure the total length of ducting needed. [. . . ]