User manual MIELE DA 329-1I

[. . . ] Operating and Installation Instructions Ventilation System DA 326-1 i DA 329-1 i To prevent accidents and machine damage, read these instructions before installation or use. UV M. -Nr. 40 3 IMPORTANT SAFETY INSTRUCTIONS Read these Operating Instructions carefully before installing or using the Ventilation System. This appliance is intended for residential use only. The manufacturer cannot be held responsible for damages caused by improper use of the hood. Improper use of the appliance can lead to personal injury and material damage. [. . . ] These are shown on the data plate which is visible when the grease filter is removed. 18 Installation Instructions 20 Caring for the environment Disposal of packing material The cardboard box and packing materials protect the appliance during shipping. To prevent suffocation of children, ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of their reach. Disposal of an old appliance Old appliances may contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Before discarding an old hood, unplug it from the outlet and cut off its power cord to prevent hazards. 21 IMPORTANT SAFETY INSTRUCTIONS Do not install this exhaust hood over cooktops burning solid fuel. When installing the hood, make sure that the following minimum distance (S) between the top of a Miele cooking surface and the bottom of the hood is: - 18" (45 cm) above electric cooktops - 26" (65 cm) above gas cooktops - 26" (65 cm) above an open grill For non-Miele cooking appliances maintain the safety distances recommended by the cooktop manufacturer in their instructions. If there is more than one appliance beneath the hood and they have different minimum safety distances always select the greater distance. See "Important Safety Instructions" for further information. If there is any doubt concerning installation, contact the Technical Service Department. USA 1-800-999-1360 techserv@mieleusa. com CDN 1-800-565-6435 service@miele. ca , During the installation process, please be careful of sharp edges that can cause harm. 22 Electrical data All electrical work should be performed by a qualified electrician in strict accordance with national and local safety regulations. Installation, repairs and other work by unqualified persons could be dangerous. Ensure that power to the appliance is "OFF" while installation or repair work is performed. Verify that the voltage, load and circuit rating information found on the data plate (located behind the grease filter), match the household electrical supply before installing the hood. If there is any question concerning the electrical connection of this appliance to your power supply, please consult a licensed electrician or call Technical Service. USA 1-800-999-1360 CDN 1-800-565-6435 WARNING: THIS APPLIANCE MUST BE GROUNDED Important The hood comes equippped with a 5 ft (1. 5 m) power cord with a NEMA 5-15 molded plug for connection to a 120 VAC, 60 Hz, 15 A power outlet. 15 A 23 Appliance dimensions DA 326-1 i DA 329-1 i * 1) The slot for the active charcoal filter must be accessible if the hood is being used in recirculation mode. 2) The rear panel of the cabinet may have to be removed for these dimensions to be applicable. 3) DFB light shield (optional accessory) To ensure that the exhaust ducting can be installed on the exhaust connection easily, the upper cabinet must be at least 18 1/8" (460 mm) high. *The DA 329-1 i can also be built into a 23 5/8" (60 cm) cabinet. In this case, the lower portion of the hood will overlap the bottom cabinets on either side. 24 Appliance dimensions Metric conversion table Millimeters 3 10 15 19 30 40 50 70 75 85 88 125 150 170 175 190 245 255 258 270 273 275 285 345 420 460 470 562 568 595 600 895 900 6 Inches 1 3 9 /8 /8 /4 /16 3 1 /16 1 9/16 1 15/16 2 3/ 4 3 3 3/ 8 3 1/ 2 5 6 11 3 /16 6 7/ 8 7 1/ 2 9 5/ 8 10 1/16 10 3/16 10 5/8 10 3/4 10 13/16 11 1/4 13 9/16 16 9/16 18 1/8 18 1/2 22 1/8 22 3/8 23 7/16 23 5/8 35 1/4 35 7/16 25 Appliance dimensions Installation in cabinetry The depth of the installation depends on what type of light shield is used and the dimensions of surrounding cabinetry. Hood installed with a DFB light shield (optional accessory) To install the hood so that the light shield is flush with the adjacent cabinetry, the following dimensions must be used. (Please refer to the metric conversion table) Hood installed with a custom made light shield A custom made, matching light shield can be mounted on the hood. [. . . ] When installing the ventilation grill make sure that the slats in the grill point towards the center of the room and not towards a wall or the ceiling. ^ The vent connection (vent socket) a and the exhaust grill b must be joined together with a pipe or flexible duct c cut to size. 14. Electrical connection Refer to the notes in "Electrical connection" and "Important Safety Instructions" before connecting to electricity. ^ Plug in the power cord. 38 Installation Special installation instructions 27 9/16" (70 cm) width cabinet 35 7/16" (90 cm) width cabinet ^ The measure "x" will be calculated as described for a 23 5/8" (60 cm) cabinet. [. . . ]