User manual MIELE CS 1326Y TEPAN YAKI COMBISET CUSTOMIZED COOKING SURFACE OPERATING AND INSTALLATION MANUAL

[. . . ] installed and grounded by a qualified technician. ~ Install the appliance so that the power cord does not come into contact with any portion of the cooktop which may become hot during use. damaged cord or plug, or if the appliance has been damaged in any manner. outer casing of the appliance. ~ Before servicing, disconnect the ~ Be sure your appliance is properly ~ Before installing the Tepan Yaki, ~ Be certain your appliance is ~ Do not operate any appliance with a check for externally visible damage. To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system. [. . . ] The cooking time depends on the type, preparation, and thickness of the food item. 10 Use Grilling tips Before each use, wipe the griddle with a damp cloth, to remove dust or other residue. ­ It is best to pre-heat the appliance for 8-10 minutes, at the preferred cooking temperature. ­ When cooking meat, the appliance should be hot, otherwise too much moisture will be lost from the meat. ­ Generally, the appliance requires very little fat or oil for cooking, and none is needed for marinated items. If you are using some fat or oil, do not add it to the appliance until the temperature control light has switched off. ­ To minimize splattering, dry moist foods with a paper towel before cooking. 11 Cleaning and care , Do not use a steam cleaner to ^ Turn the appliance off, and allow it to cool. ^ Place a mild solution of warm water and liquid dish soap on the Tepan Yaki and allow it to soak. ^ Remove the built-up debris with a spatula and wipe clean with a damp cloth. ^ Thoroughly clean the appliance with a few drops of stainless steel cleaner (available from Miele) using a damp cloth. ^ Wipe off the cleaner with water and dry the appliance with a clean, dry cloth. Do not use stainless steel conditioners on the appliance. clean this appliance. Steam could penetrate electrical components and cause a short circuit. ­ Do not use any sharp or pointed objects which could damage the seal between the frame and the countertop. ­ Never use scouring agents, pads, abrasive cleaning agents, or strong cleaners, e. g. grill or oven sprays, stain or rust removers, these could damage the surface of the appliance. ­ Avoid cleaning products that contain washing soda, acids/alkali, ammonia, bleach, or lime removers. 12 Frequently asked questions , Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. What if the appliance does not heat up after it is turned on?However, under certain conditions it may be possible for installation in these applications. Please contact the Miele Technical Service Department with specific requirements. arranged in such a way that it remains easily accessible once the appliance has been installed. ~ The electrical connection should be ~ You must ensure the power cable ~ The appliance must not be ~ The countertop must be bonded with heat resistant (212°F/100°C) adhesive to prevent distortion or dissolving. ~ To eliminate the risk of burns or fire by reaching over heated surfaces cabinet storage space above the appliance should be avoided. If cabinet storage is necessary, the risk can be reduced by installing a venting hood to project horizontally a minimum of 5" (127 mm) beyond the bottom of the cabinets. for the appliance will not be subject to any mechanical strain after installation. [. . . ] Black : connect to L1 (hot) Red: connect to L2 (hot) Green: connect to GND (ground): 240 V, 60 Hz, 15 A fuse rating Be sure the power outlet is accessible after installation. For further information, see the wiring diagram provided with the appliance. servicing, disconnect the power supply by either removing the fuse, shutting off the main power or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Before connecting the appliance to the power supply, make sure that the voltage and frequency listed on the rating label correspond with the household electrical supply. Only operate the appliance after it has been installed into the countertop. [. . . ]