User manual MIELE CRYSTAL G 5105

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MIELE CRYSTAL G 5105. We hope that this MIELE CRYSTAL G 5105 user guide will be useful to you.


MIELE CRYSTAL G 5105 : Download the complete user guide (2882 Ko)

Manual abstract: user guide MIELE CRYSTAL G 5105

Detailed instructions for use are in the User's Guide.

[. . . ] Operating Instructions Dishwasher G 5100 G 5105 To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M. -Nr. 62 3 IMPORTANT SAFETY INSTRUCTIONS WARNING ­ When using your dishwasher, follow basic precautions, including the following: Electrical Safety ~ Before installation, make sure that Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. Keep these operating instructions in a safe place and pass them on to any future user. the voltage and frequency listed on the data plate correspond with the household electrical supply. disconnect the power supply to the work area by unplugging the unit, "tripping" the circuit breaker or removing the fuse. [. . . ] The horizontal marks in compartment II indicate the levels of approximately 1 ¼ and 2 tablespoons (20 and 30 ml) respectively. The marks indicate the approximate fill level in ml when the door is open in a horizontal position. 33 Use Turning on ^ Make sure the spray arms can rotate freely. The "Start/Stop" indicator light flashes and the indicator of the last set program lights up. Starting a program ^ Press the "Start/Stop" button. The "Start/Stop", "Cleaning" indicators and the indicator of the selected program come on. If additional options are selected, the corresponding indicators will also light up. the water softening) may be interrupted. Selecting a program Choose your program according to the type of load and soiling. You can now select the additional options (see "Additional Options"). Progress indicator After starting a program, the progress indicator will show the current program section. 34 Program Guide Program guide When to use Pre-rinse 1 2 Program sequence Main wash X Interim rinse 1 2 Final Drying rinse X X Pots & Pans For normally soiled pots & pans with dried on food, and heavily soiled dishware, use 120% detergent recommended. Program for completely washing a full load of normally soiled dishware with the ability to adjust energy and water consumption based on the soil load of the dishware. For temperature sensitive glassware and lightly soiled dishware, use 50% detergent recommended. party dishware or to remove salt traces from the wash cabinet after refilling salt, not suitable for detergent tabs. To rinse dishes when a complete program is not needed. X Normal as required X X X X China & Crystal as required X as required X X SaniWash X X X X Express X X X X Rinse & Hold X Usage: Electrical - 0. 01 - 1. 23 kWh Water - 1. 3 - 6. 3 gal (5 - 24 l) 35 Use Standby A few minutes after the last key is pressed or at the end of the program the dishwasher switch into Standby mode to save energy. The indicators and time display (where appropriate) can be turned off and only the Start/Stop indicator light flashes slowly. If you do not turn the dishwasher off after the program ends, it will turn completely off after a few minutes in standby mode (see "Settings - Optimize standby"). If refill salt and/or rinse aid or a fault are present in the display, the dishwasher will not go into Standby mode. At the end of a program At the end of a program the display shows End. The drying fan will continue to run for a few minutes at the end of the "Express" program. You can now open the dishwasher and remove the dishes. , To avoid damage to counter tops rom steam, open the door after the end of the program either fully (never ajar) or keep it closed until you are removing all the dishes. Turning off At the end of a program: ^ Press the K button to turn the dishwasher off. The dishwasher continues to use electricity until turned off with the K button. The refill messages can be turned off when you use a tab detergent (see "Before using for the first time"). Fault messages cannot be turned off. Preparing your appliance for an extended vacation If you elect to turn off the water to your home for an extended period of time, please note that this may not be enough to reduce the risk of a leak. To be completely safe, you must turn off the water supply to each individual appliance. This means under the sink for a dishwasher, at the laundry bib for your washer, etc. 36 Use Unloading the dishwasher Dishes tend to break and chip more easily when they are hot. Allow the dishes to cool until they are comfortable enough to handle before unloading them. If you open the door fully after switching off, the dishes will cool much faster. [. . . ] If there is any question concerning the proper electrical connection or grounding of this appliance to the power supply, please consult a licensed electrician or call Miele's Technical Service Department: U 1-800-999-1360 V 1-800-565-6435 Specifications The dishwasher comes equipped with a 4 ft (1. 2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle. 59 Electrical connection Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable. , CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer cannot be held responsible. Before connecting the appliance to the power supply, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. , Prior to making a hardwire connection to the terminal, remove the power cord. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MIELE CRYSTAL G 5105




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MIELE CRYSTAL G 5105 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.