User manual MIELE G 4270 SCVI

[. . . ] Operating Instructions Dishwasher G 4270 G 4275 To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M. -Nr. 52 3 IMPORTANT SAFETY INSTRUCTIONS WARNING ­ When using your dishwasher, follow basic precautions, including the following: Electrical Safety ~ Before installation, make sure that Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. Keep these operating instructions in a safe place and pass them on to any future user. the voltage and frequency listed on the data plate correspond with the household electrical supply. disconnect the power supply to the work area by unplugging the unit, "tripping" the circuit breaker or removing the fuse. [. . . ] If the door is closed, the program will continue from where it was interrupted. , Open the door with care. Close the door firmly until it clicks into place. Changing a program If the detergent flap is already open, do not change the program. If a program has already started and you wish to change it: ^ Open the door. ^ Start the program by closing the door. 27 Program Guide Program guide When to use Pre-rinse 1 2 Program sequence Main wash X Interim rinse 1 2 Final Drying rinse X X Pots & Pans For normally soiled pots & pans with dried on food, and heavily soiled dishware, use 120% detergent recommended. Program for completely washing a full load of normally soiled dishware with the ability to adjust energy and water consumption based on the soil load of the dishware. For normally soiled dishware, energy saving program with a long soaking time and a low temperature To sanitize dishware, e. g. party dishware or to remove salt traces from the wash cabinet after refilling salt, not suitable for detergent tabs. To rinse dishes when a complete program is not needed. X Normal as required X X X X Economy X X X X SaniWash X X X X Express X X X X Rinse & Hold X Usage: Electrical - 0. 01 - 1. 23 kWh Water - 1. 3 - 6. 3 gal (5 - 24 l) 28 Additional options Buzzer A signal sounds at the end of a program and when a fault occurs. The buzzer at the end of a program sounds five times in quick succession for up to one hour. ^ Press the "Program" button and at the same time turn the dishwasher on with "g". ^ Hold the program button until the "Rinse & Hold" program indicator comes on. The "Intake / Drain" indicator flashes four times in intervals. The setting can be recognized by the flashing of the "SaniWash" indicator: ­ flashing: buzzer is activated ­ not lit up: buzzer is deactivated ^ To change the setting press the "Program" button for at least one second, until the "Intake / Drain" indicator lights up. ^ Turn the dishwasher off "o". 29 Additional options Default settings All settings can be reset to the factory default. ^ Press and hold the "Program" button and at the same time turn the dishwasher on "g". Hold the "Program" button until the "Rinse & Hold" program indicator comes on. The "Intake / Drain" indicator flashes once long and twice short in intervals. The setting can be recognized by the flashing of the "SaniWash" indicator: ­ flashing: all settings are factory default ­ not lit up: at least one setting was changed ^ To change the setting press the "Program" button for at least one second, until the "Intake / Drain" indicator lights up. ^ Turn the dishwasher off "o". 30 Frequently asked questions With the aid of the following guide, minor problems can be fixed without a service call. , Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Problem The program does not start. ­ Contact Miele Technical Service. The drain pump is running when the door is opened. The waterproof system has activated. 31 Frequently asked questions Problems with water Intake / Drain Problem Shortly after the program start the dishwasher stops running. The "Intake / Drain" indicator flashes when the door is open. [. . . ] If there is any question concerning the proper electrical connection or grounding of this appliance to the power supply, please consult a licensed electrician or call Miele's Technical Service Department: U 1-800-999-1360 V 1-800-565-6435 Specifications The dishwasher comes equipped with a 4 ft (1. 2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle. 49 Electrical connection Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable. , Prior to making a hardwire , CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer cannot be held responsible. Before connecting the appliance to the power supply, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. connection to the terminal, remove the power cord. [. . . ]