User manual MIELE G 4205 SC

[. . . ] Operating Instructions Dishwasher G 4205 To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M. -Nr. 50 3 IMPORTANT SAFETY INSTRUCTIONS WARNING ­ When using your dishwasher, follow basic precautions, including the following: Electrical Safety ~ Before installation, make sure that Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. Keep these operating instructions in a safe place and pass them on to any future user. the voltage and frequency listed on the data plate correspond with the household electrical supply. disconnect the power supply to the work area by unplugging the unit, "tripping" the circuit breaker or removing the fuse. [. . . ] The dishwasher continues to use electricity until turned off with the s button. vacationing, turn off the water supply. Preparing your appliance for an extended vacation If you elect to turn off the water to your home for an extended period of time, please note that this may not be enough to reduce the risk of a leak. To be completely safe, you must turn off the water supply to each individual appliance. This means under the sink for a dishwasher, at the laundry bib for your washer, etc. Interrupting a program A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted. , Open the door with care. Close the door firmly until it clicks into place. Changing a program If the detergent flap is already open do not change the program. If a program has already started and you wish to change it: ^ Press the "Start/Stop" button for at least one second. ^ Select and start the desired program. 27 Program Guide Program guide When to use Pre-rinse 1 2 Program sequence Main wash X Interim rinse 1 2 Final Drying rinse X X Pots & Pans For normally soiled pots & pans with dried on food, and heavily soiled dishware, use 120% detergent recommended. Program for completely washing a full load of normally soiled dishware with the ability to adjust energy and water consumption based on the soil load of the dishware. For normally soiled dishware, energy saving program with a long soaking time and a low temperature To sanitize dishware, e. g. party dishware or to remove salt traces from the wash cabinet after refilling salt, not suitable for detergent tabs. To rinse dishes when a complete program is not needed. X Normal as required X X X X Economy X X X X SaniWash X X X X Express X X X X Rinse & Hold X Usage: Electrical - 0. 01 - 1. 23 kWh Water - 1. 3 - 6. 3 gal (5 - 24 l) 28 Additional options Default settings All settings can be reset to the factory default. ^ Press the "Start/Stop" button and at the same time turn the dishwasher on "s". Hold the "Start/Stop" button until the "Start/Stop" indicator comes on. The bottom program indicator flashes once long and twice short in intervals. ­ The "Cleaning" indicator flashes: All settings are the factory default. ­ The "Cleaning" indicator is off: At least one setting was changed. ^ To reset the dishwasher to the default settings, press the "Start/Stop" button. ^ Turn the dishwasher off "s". 29 Frequently asked questions , Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Problem The Start / Stop indicator does not flash after the dishwasher is turned on with "s". The program cycle indicators "Cleaning", "Drying" and "End" flash at the same time. See data plate for minimum amperage. The fuse has tripped. The drain pump is running when the door is open. There may be a technical ­ Turn the dishwasher off fault. [. . . ] Repairs and service by unqualified persons could be dangerous and the manufacturer cannot be held responsible. Before connecting the appliance to the power supply, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. connection to the terminal, remove the power cord. Otherwise there will be a risk of electric shock from the attached plug. An existing flexible supply cord or cable shall have a minimum thickness of AWG 14. [. . . ]