User manual MIDLAND NAUTICO 1

[. . . ] 1-1999 Edition - National Council on Radiation Protection and Measurements (NCRP) of the United States, Report 86, 1986 - International Commission on Non-lonizing Radiation Protection (ICNIRP) 1998 To control your exposure and ensure compliance with the general population or uncontrolled environment exposure limits, transmit no more than 50% of the time. The radio generates measurable RF energy exposure only when transmitting. IMPORTANT: Changes or modifications to this unit not expressly approved by MIDLAND RADIO CORP. your radio is set up to transmit a regulated signal on an assigned frequency. [. . . ] When you press the PTT button to transmit on an active channel, the scanning function will stop and remain on the active channel. INSTANT CHANNEL 9/16 Channel 16 (Distress Channel) is used for calling other stations or for distress alerting. You can also switch to Channel 9, the leisure-use call channel, without changing your normal channel by pressing and holding the CH9/16 button for 1 second. pressing the CH9/16 button again returns the radio to the normal channel setting. CALL TONE Your NAUTICO1 can transmit a call tone for a fixed length of time. The TX icon will appear while transmitting a call tone and a tone can be heard on the speaker for confirmation. KEYPAD LOCK To avoid accidentally changing the radio setting, press the MENU button 4 times then press an up/down button to choose ON. To unlock the keypad, press the MENU button once, then press the / button to choose OF. The display illumination can also be activated when the MENU button is pressed. CHANNEL SELECTION Press the MENU button once, and then the / buttons to select one of the channels. To confirm the selection, press the PTT button or press MENU again to move to the next feature setting. To select the power level on channels press the MENU button two times, a "Pr" icon will appear blinking on the display. To confirm, press the PTT button or press MENU again to move to the next feature setting. The display shows "eVOX" blinking while on the right of the CHANNEL NUMBER display, an "oF" icon appears. Select "1" or "2" by pressing the / buttons and push the PTT key, or press MENU again to move to the next feature setting. EVOX will be more sensitive on the "2" setting than on the "1" setting. Select "oF" by pressing the / buttons and push the PTT key, or press MENU to move to the next feature setting. ROGER BEEP (end of transmission) TONE When the PTT button is released, the radio will beep to confirm to other users that your transmission has finished. To turn the ROGER BEEP tone on, press the MENU button until the display shows an "rb" icon while on the right of the "rb" display, an "oF" icon appears. Select "on" by pressing the / buttons and push the PTT key, or press MENU to move to the next feature setting. To turn the ROGER BEEP tone off, press the MENU button until the display shows an "rb" icon while on the right of the "rb" display, an "on" icon appears. Select "oF" by pressing the / buttons and push the PTT key, or press MENU to move to the next feature setting. [. . . ] S = Simplex ; D = Duplex ; * = obligatory low transmission power of 1 Watt ** = classified to DSC communications Midland Radio Corporation will repair or replace, at its option without charge, any Midland VHF MARINE transceiver which fails due to a defect in material or workmanship within Three Years following the initial consumer purchase. Accessories have a 90 day warranty from date of purchase, including any antennas, chargers, or earphones. This warranty does not include the cost of labor for removal or re-installation of the product in a vehicle or other mounting. Performance of any obligation under this warranty may be obtained by returning the warranted product, prepaid freight, along with proof of purchase to: Midland Radio Corporation Warranty Service Department 5900 Parretta Drive Kansas City, MO 64120 This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. [. . . ]