User manual MIDAS CONSOLES MIDAS LEGEND 3000

[. . . ] OPERATORS MANUAL Klark Teknik Group Klark Teknik Building Walter Nash Road Kidderminster Worcestershire DY11 7HJ England Tel: +44 1562 741515 Fax: +44 1562 745371 Email:Sales@ktgplc. com Websites: www. midasconsoles. com www. klarkteknik. com MIDAS Legend 3000 Console Operators Manual DOC02-L3000 Issue 1. 2 - March 2004 Due to a policy of continual product improvement, specification and features may be subject to change without notice. IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AVIS: RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR These symbols are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. [. . . ] Navigation of the menu is achieved by using the UP/DOWN switches to select an entry and then pressing CONFIRM to execute the selected function or sub menu. The CHECK switch provides a preview of the input module MUTE STATUS for any of the snapshot screen WITHOUT recalling the ACTUAL setting to the console surface (mutes are displayed on the ASSIGN LEDs so that the current mute status is always present and accurate). Whist in check mode the ACT/ SCENE C/O, and UP/DOWN switches can be used to step through the snapshots. CONFIRM and CANCEL are used to enter or exit functions or sub menus. insert delete copy check cancel confirm act scene act/scene down c/o up last now next 29 lock s-i-p (hold 3secs) active system a b store midi system insert delete copy Snapshots can be stored in the automation system as ACTs or SCENEs. There is no difference between an ACT or a SCENE apart from the numbering; scenes are just sub sets within acts. check cancel confirm The ACT/SCENE C/O switch is used to select the acts or scenes in conjunction with the UP/DOWN switches. An appropriate indication, "ACT" or "SCENE", will be illuminated to indicate this status. act scene act/scene down c/o up The UP/DOWN switches allow the operator to scroll through act/scene numbers and navigate through menus. The LAST, NOW and NEXT switches recall snapshots to the console surface. LAST recalls the snap shot numerically preceding the snap shot that is currently recalled/stored. last now next NEXT recalls the snapshot numerically proceeding the snapshot that is currently recalled/stored. NOW recalls the snap shot that is currently indicated on the numeric display. 30 Monitor Section The SIS switch routes solo signals to the mono and stereo local monitor outputs with full left, centre, right imaging. This overrides any signals sent from other sources when ever a solo is active on the console. The STEREO SOLO TRIM adjusts the incoming solo level before sending it to the monitor output. The control range is from +6dB to off with a centre detented 0dB calibration point. The MONO SOLO TRIM adjusts the incoming solo level before sending it to the monitor output. The control range is from +6dB to off with a centre detented 0dB calibration point. The mono SOLO switch routes solo signals to the mono local monitor output when ever a solo is active on the console. The MONO master switch routes the post fader mono master mix to the mono local monitor output. On input channels and stereo returns the MON switch changes the monitor signals to be derived from the monitor signal paths where appropriate. The LOCAL MONITOR level control gives continuous adjustment of all three local monitor output levels from + 10dB to off. The SOLO PFL switch sends the mono PFL solo bus signals to the headphones and local monitor outputs in place of the AFL signals. This also changes the solo meters to monitor PFL solo bus signals. monitor source 0 0 mono solo +6 stereo solo +6 SOLO MONO SIS SOLO MONO ST TAPE The stereo SOLO switch routes solo signals to the stereo local monitor outputs when ever a solo is active on the console. This overrides any signals sent from the mono master, stereo master or tape input. The MONO master switch routes the post fader mono master mix to the stereo local monitor outputs. input output f. o. h. stereo mono MON 0 0 The ST master switch routes the post fader stereo master mix to the stereo local monitor outputs. The TAPE switch routes the stereo tape input to the stereo local monitor outputs. The PHONES level control gives continuous adjustment of the headphone level from + 10dB to off. [. . . ] Using the browse function select the show you wish to download into the console and click on OK. 3/ Select the Show menu in Hsutil and click on 'Upload To Console'. 4/ Select the SYSTEM menu on the L3000, and scroll to 'DATA' then press 'CONFIRM'. 6/ When the file is uploaded successfully, the L3000 will prompt you to press CONFIRM. [. . . ]