User manual MIDAS CONSOLES HERITAGE 2000 DOC02 H2000

[. . . ] OPERATORS MANUAL Midas Klark Teknik Building, Walter Nash Road, Kidderminster. Tel:+44 1562 741515 Fax:+44 1562 745371 Email: midas. info@uk. telex. com Website: midasconsoles. com MIDAS Heritage 2000 Operators Manual DOC02-H2000 Issue 1. 4 - July 2002 Due to a policy of continual product improvement, specification and features may be subject to change without notice. IMPORTANT SAFETY INSTRUCTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AVIS: RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR These symbols are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] The switches can be controlled from snapshot automation. mute mute The mute SAFE switches remove the matrix mutes from snapshot automation. The SPLIT switch changes the matrix AFL solos from mono to stereo. SAFE SOLO SAFE split The SOLO switches send matrix signals to the PFL mono and AFL stereo busses. If a SOLO switch is pressed for a short time it will latch on or off, but, if it is held on for more than 1 second the latching is disabled and when the switch is released the channel solo will turn off. As a default the solo system is auto cancelling so each new solo cancels the last. This function is time dependant which allows several solos to be active as long as they are switched on at approximately the same time, i. e. to solo both sides of a stereo mix press both solo switches at the same time. Alternatively the SOLO ADD MODE switch on the MONITOR module can be used to defeat the auto cancelling and allow multiple channel monitoring. In this mode input channel solos have priority over the matrix solos and will temporarily override them. When the input solos are cancelled the matrix solos will be active again. solo solo 10 The MATRIX faders give continuous adjustment of the matrix output levels from + 10dB to off. 5 0 5 10 20 30 40 dB matrix MIDAS 34 HS0041 Automation assign keys mode switches lock a u t o 1 2 3 4 5 f a s t s c e n e automation system store midi system insert delete copy vca 1 2 3 4 5 6 7 8 9 10 check cancel confirm mute fader m u 6 7 8 9 10 act act/scene c/o down scene up virtual fader recall mode t e last now next a b s s MIDAS 35 Assignment Control The LOCK switch will toggle state each time it is pressed. When the LOCK switch is illuminated all assignment changes are disabled and virtual fader operation is locked (either on or off). The console will automatically revert to a locked state if no assignment controls are operated within a 90 second period. The VCA, MUTE and FADER switches set the current assignment/display mode for the fader tray LED's. As a default these switches interlock so that only one mode can be viewed at a time. However if Mute and VCA are pressed down for more than 0. 5 second the interlock is removed. If the console is in VCA or MUTE mode, the ASSIGN KEYS can be used to change settings for input VCA assignment or automute assignment in conjunction with the SET switch on each channel as follows:To enter ASSIGNMENT mode first press the LOCK switch (to un-lock the assignment system). Press the ASSIGN KEYS to set up the required group number or numbers; a long press will allow multiple assignment where as a short press will clear the previous settings. Press the SET switch on the input channels to which the assignment is required. Again there are two ways to do this; a long press will remove all prior settings on the input and replace them with the new assignment; a short press will toggle the state of any switches within the assignment set up. Pressing the input SET switch will cause that channel to toggle the number one and two assignments for the channel either from off to on or visa versa. To switch the assign keys off simply press the ones that are illuminated which will toggle them off. In this mode operating an input SET switch with a long press will clear all the VCA and /or automute assignments. press VCA mode to clear VCA's, press MUTE mode to clear automutes, or use a long press to activate both VCA and MUTE mode for simultaneous clearing. assign keys mode switches lock vca 1 2 3 4 5 6 7 8 9 10 mute fader virtual fader recall mode a b The VIRTUAL FADER switch enables the operation of the virtual fader system. [. . . ] d/ Pressing CONFIRM will then synchronize the console with the system. Note When a console is in slave mode CONS is the only item of the SYSTEM menu that can be accessed. If a slave console is reconfigured to be a master it will automatically make the original master console a slave when the CONFIRM button is pressed. 50 Cable Specification H1000 / H2000 / H3000 Qty Manufacturers' Reference KT Part No. CON31-5MXB CON31-5FXB Neutrik: NC5MXB Neutrik: NC5FXB Farnell: 152-133 Cable Core Cable Colour NA BLUE GREEN RED NA TIN White No Connection CABLE CORE 1 CABLE CORE 3 CABLE CORE 2 No Connection Braid Screen Cable Core 4 CAN CABLE HS-CAN-8-01 Page 1of 1. ACBLX-1606-1 Item 2 1 8m Signal NA CAN_L 0V CAN CAN_H NA CHASSIS NA 1. [. . . ]