User manual MICROTEK MAC M TAKEIT350 1100

[. . . ] 2 Camera Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting Ready . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Basic Picture Taking Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Instant image frames erasure All images can be cleared instantly to start a new picture taking session. · Low power consumption with auto energy-save mode New batteries can take up to 1000 shots. Camera automatically enters into "sleep" (energy-saving) mode when it remains inactive for 30 seconds. · Supports USB interface With USB, download of images to your Mac is accomplished at higher speed. · Camera Driver For Macintosh users, the utility CD that accompanies your camera only includes the Macintosh camera driver. 2 Camera Components GRIP LENS SHUTTER BUTTON USB PORT BATTERY COMPARTMENT LOCK BATTERY COMPARTMENT LCD DISPLAY PANEL VIEWFINDER TRIPOD MOUNT POWER AND FUNCTION MODE SELECTION BUTTON STRAP MOUNT 3 Getting Ready A. Loading the Battery (4 AAA size batteries, Alkaline recommended) BATTERY COMPARTMENT LOCK LIFT away from the camera to unlock 1 Unlock the battery compartment cover by sliding its lock toward "OPEN" position. 2 Slide compartment cover outward (as indicated by the arrow shown on top of the cover) and open the cover. 3 Insert each of the 4 AAA batteries into its chambers making sure that the positive (+) and negative (-) ends are properly oriented with the polarity indicated on top of each chamber and at the back of the cover. 4 Close and slide the battery compartment cover back to its original position and lock the cover. WARNING: When the LCD Panel display starts to blink, it indicates that the batteries power is low. Stop taking pictures and transfer the images data to your PC within a week before the batteries completely lose its power. Otherwise, all the images will be erased. 4 Slide toward arrow direction to open + _ + _ Correct battery polarity at outer end of the compartment are indicated at the back of cover or as illustrated above. B. Basic Picture Taking Operation NOTE: NOTE The camera is designed without a power switch. If the camera is off, press the Function Mode button to turn the camera back on. 1 With the camera strap looped around your wrist, hold the camera by its grip. Adjust size of your composition by increasing or decreasing distance between camera and subject but not nearer than one meter. A short beep sound emits at each click of the shutter to confirm that a shot has been taken and the camera is ready to take the next picture. NOT E: 26 or 107 shots mode is available with erase capability (see next page for details). After each shot, the LCD Panel will show the number of remaining shots available. WARNING: A warning beep (longer and lower tone compared to normal beep) will emit if exposure is too dark for a normal picture taking. No image is taken when this condition occurs. 5 Other Modes of Operation A 107 Shots mode . This mode of operation allows you to take 107 shots of lower-resolution images in (320 x 240) QVGA format. To set your camera into 107 shot modeLr 1 Repeatedly press the Function Mode button until the "L " icon is displayed on the LCD Display Panel. 2 2 Press the Shutter button and the "Lr" icon becomes "99" which would indicate that the 107 Shot mode is ready. For the "Lr" mode, the LCD screen will only show "99" pictures. of pictures taken (in between these 8 shots) will not be deducted from "99" until you take the 9th shot. NOT : Switching from 107 pictures mode to 26 pictures modes will not erase any images in E the camera. If you attempt to continue shooting at the end of 107th shot, a repetitive beep will emit when you press the Shutter button. 107 Shots mode is ready only when the LCD Panel displays the "9 9 " icon 99 When the "L r" icon appears on the LCD Panel, press Shutter to display the "99" icon Repeatedly press this Function Mode button until the "Lr " icon is r displayed 6 B. [. . . ] 2 Press the Shutter button twice to start erasing all images in the camera. NOTE: If you do not press the Shutter a second time within 5 seconds, the erase function is aborted. "All-Frame-Erase" is ON when this LCD Panel displays the " CL " icon Press the Shutter button to start the delay countdown Repeatedly press this Function Mode button until the "All-Frame-Erase" icon is displayed 10 Connecting the Camera to your Mac To transfer (download) the image data from the camera to your Macintosh, connect the camera to your Mac with the supplied USB cable. 1 Insert the smaller terminal of the USB cable into the camera's USB port. 2 Plug the other end of the USB cable into the USB port of your Macintosh. 3 To perform downloads and to operate the camera as web camera using your Macintosh, Please refer to the README file for a more detailed instructions on installation and image downloads. 11 Camera Driver Installation A. [. . . ]