User manual MICROTEK GNC M MS4 0704

[. . . ] User's Manual MS4 DLP Projector www. microtek. com Conference Projectors Copyright This publication, including all photographs, illustrations and software, is protected under international copy right laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright July , 2004 Disclaimer The information in this document is subject to change without notice. The manufacturer makes no repr esentations or warranties with respect to the contents hereof and specifically disclaims any implie d warranties of merchantability or fitness for any particular purpose. [. . . ] The projector prepares for shutdown and a "Wait a moment please. . . " message appears. 6. When the "Power Off?/Press Power again" message appears, press the Power button. The projector turns off. Adjusting the Projector Level Take note of the following when setting up the proj ector: · · · The projector table or stand should be level and sturdy. Be sure cables are not in the way or can cause the projector to be knocked over. 1. To raise the level of the projector, lift the projector [A] and press the height-adjuster button [B]. 3. To make minor adjustments, rotate the side foot [D]. To lower the level of the projector, press the height-adjuster button and push down on the top of the projector. Adjust the Zoom, Focus and Keystone 1. Use the Image -focus control (on the projector only) to sharpen the projected image . 2. Use the Image -zoom control (on the projector only) to resize the projected im age and screen size . 3. Use the Keystone buttons (on the projector or the remote control) to correct image-trapezoid (wider top or bottom) effect . The keystone control appears on the display. Adjusting the Volume 1. Press the Volume +/- but tons on the projector or the remote control. The volume control appears on the display. 2. Use the Volume +/- but tons to adjust the level. 3. 4. Press the Mute button (on the remote control only) to turn off the volume. Press any Volume +/buttons on the projector or the remote control to turn off mute. ON-SCREEN DISPLAY MENU SETTINGS On-Screen Display Menu Controls The projector has an On-Screen Display (OSD) that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the remote control and on the projector. Note: Depending on the video source not all items in the OSD are available, items that can not be changed are grayed out. Setting the OSD Language You may want to reference the OSD on your projector while reading this section. Press the cursor button until the language you want is highlighted. Press the Menu button twice to close the OSD. Main Menu Press the Menu button to open the OSD menu. Press the cursor button to move up and down in the Main menu. ITEM Brightness Contrast Sharpness Color Temperature Color Satur ation Color Tint Gamma Press the cursor Press the cursor Press the cursor D ESCRIPTION button to adjust the brightness. (Range: 0 -- 100) button to adjust the display sharpness (Range: 1-5) DEFAULT 50 50 3 Normal Press the cursor button to adjust the video tint/hue. (Range: Cool/Normal/Warm) Press the cursor Press the cursor Press the cursor Input PC MAC Video Chart B&W button to adjust the video saturation. Gamma 2. 2 1. 8 2. 4 2. 2 2. 4 Brightness High High Low Low High 50 50 PC Color Space Reset Press the cursor button to adjust the color space. (Range: Auto ­ RGB ­ YPbPr - YCbCr ) Resets all Quality items settings to default values Auto - Setup Menu Press the Menu button to open the OSD menu. Press the cursor button to move up and down in the Setup menu. ITEM Horizontal Position Vertical P osition Keystone Press the cursor DESCRIPTION button to move the image left or right. (Range: 0-- 100) DEFAULT 50 Press the cursor button to move the image up or down. (Range: 0-- 100) 50 Press the cursor button to correct distortion of the projected image. (Range: -20 -- +20) Press the cursor button to toggle betwee n the 4:3 standard format and 16:. 9 High Definition TV (HDTV) format. Resets Keystone and Aspect Ratio to default values 0 4:3 Aspect Ratio Reset Config Menu Press the Menu button to open the Main menu. Press the cursor button to move up and down in the Config menu. ITEM Blank Screen Auto Source Auto Power Off Volume Menu Position Menu Display Translucent Menu Reset DESCRIPTION Press the cursor button to select a background color for blank screen (Range: Black ­ Red ­ Green ­ Blue ­ White) Press the cursor (Range: On ­ Off) button to enable or disable automatic source detection DEFAULT Blue On On 4 Center 15 Off Press the cursor button to enable or disable automatic shut- down of lamp after 10 min. of inactivity (Range: On ­ Off) Press the cursor button to adjust the audio volume level (Range: 0 - 8) Press the cursor button to position the OSD on screen (Range: Left ­ Right ­ Center ­ Down ­ Up) Press the cursor button to determine timeout delay of OSD (Range: 10 - 20 sec. ) Press the cursor button to set menu screen translucency (Range: On ­ Off) Resets all Options screen items to default values Utility Menu Press the Menu button to open the Main menu. Press the cursor button to move up and down in the Utility menu. ITEM Video Type Video AGC D ESCRIPTION Press the cursor button to select the Video standard (Range: Auto ­ NTSC ­ PAL ­ SECAM) Press the cursor button to enable or disable aut omatic gain control for video source. [. . . ] Use the Keystone button on the remote control or projector to correct the problem. Problem: The image is reversed or upside down 1. Check the Projection setting on the Setup menu of the OSD. Problem: The image is streaked 1. Set the Frequency and Tracking settings on the Setup menu of the OSD to the default settings. To ensure the problem is not caused by a connected PC's video card, connect to another computer. Problem: The image is flat with no contrast 1. [. . . ]