User manual MICROTEK GNC M JTXV7S XXXX

[. . . ] In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. "Le présent appareil numérique n'èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. " ii TABLE OF CONTENTS TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . III Your New LCD Monitor 1 Unpacking 1 Identifying Components 3 Adjusting the Viewing Angle 5 Connecting AC Power, Video and Audio Cable 6 Power Management System 6 The LCD Monitor's Control Panel 7 Adjusting the Monitor's Display 9 LCD Monitor Specifications 13 Supported Timing 15 LCD Monitor Wall Mounting 15 Troubleshooting 18 iii The LCD Monitor Your New LCD Monitor Your LCD Monitor has been designed to be versatile, ergonomic and user-friendly. The LCD Monitor is capable of displaying most standards, from 640x400 VGA to 1280x1024 SXGA. The digital controls located on the front panel allow the user to easily adjust the Monitor's display parameters, and the LCD Monitor's small footprint gives you more room in your workspace for other peripherals. [. . . ] When the LCD Monitor is in power-saving mode or detects an incorrect timing, the Monitor screen will go blank and the power LED indicator will start to blink. 6 The Display Controls The LCD Monitor's Control Panel Figure 2-1: The Control Panel 1. OSD Menu button Press this button to display the OSD (On-Screen Display) menu. Function button This button lets you go through the various controls available in the OSD (ex. Adjustment button 1 This button lets you go through the suboptions within a particular OSD control (ex. Adjustment button 2 This button lets you adjust the values for a particular suboption (ex. Brightness or Contrast settings under "Graphic Control" in the OSD). in Brightness), you can also use this button to decrease values. 7 5. Power Switch This button lets you turn power for the LCD monitor ON or OFF. This is also a "hot key" to close the OSD menu while it is on display. 8 Adjusting the Monitor's Display OSD Main Menu To access the OSD main menu, press the OSD Menu button. Use the Function Select buttons to scroll through the various OSD controls. The highlighted OSD control is the one that is currently selected. Analog mode Each main menu and submenu item is covered below. Pressing the OSD Menu button causes the following screen to appear (an example): Figure 2-2: The OSD Main Menu Monitor-Control Option The Monitor-Control option allows you to adjust the LCD monitor's display characteristics. H-POSITION: Moves the LCD monitor's display left or right on a horizontal plane. 9 V- POSITION: Moves the LCD monitor's display up or down on a vertical plane. RESET: Resets the H- Position, V-Position, Phase and Clock parameters. EXIT: Exits the Monitor-Control submenu. OSD-Control Option The OSD-Control option lets you adjust the position of the OSD on the screen. OSD-H-POSITION: Changes the position of the OSD on a horizontal plane. EXIT: Exits the OSD-Control submenu. Graphic-Control Option The Graphic-Control option lets you adjust the contrast, brightness, and color of the LCD monitor's display. 10 CONTRAST: Adjusts the difference between the lightest and darkest areas of the LCD monitor's display screen. BRIGHTNESS: Adjusts the level of light or brightness on the LCD monitor's display screen. The 9300 and 6500 options let you set the Color Temperature to CIE coordinates 9300° or 6500° respectively. Selecting the "User"option lets you make individual adjustments to the R, G, and B items. R, G and B: Makes individual adjustments to the Red Blue Green (RGB) gain for the color temperature Before adjusting these fields, you must select the "User" option in the Color submenu. AUTO-LEVEL: Adjusts automatically to perfect the white balance display. EXIT: Exits the Graphic-Control submenu. Misc-Control Option The Misc-Control option lets you select the OSD display language, adjust the volume setting and view system information. [. . . ] Press the upper Function Control button (refer to Chapter 2) once and then press either the upper or lower Adjustment Control button several times. If there is still no display, press the other Adjustment Control button several times. If step 2 does not work, connect your PC system to another external CRT. If your PC System functions properly with a CRT Monitor but it does not function with the LCD Monitor, and the LCD Monitor's power LED is blinking, the output timing of the PC's VGA card may be out of the LCD's synchronous range. [. . . ]