User manual MICROTEK GNC M 515C PN0232

[. . . ] In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. "Le présent appareil numérique n'èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. " Energy Star Notice As an ENERGY STAR Partner, Microtek International, Inc. has determined that this monitor meets the ENERGY STAR guidelines for energy efficiency. ii Table of Contents Introduction 1 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Usage of incorrect voltage will cause malfunction and may cause fire or electric shock. Use the VGA cable to connect the VGA connector of the LCD monitor to the VGA port of the computer. Turn on your computer, and then turn on your LCD monitor. VGA Cable: Connect with VGA cable. Power: Plug into the AC power adapter. AC/DC Adapter VGA cable Power cord Note: For added protection, the use of a Surge Protection device is recommended. The Surge Protection device should be installed between the AC Adapter and the electrical wall outlet to prevent the effects of sudden current variations from reaching and damaging the LCD monitor. 5 Operating the Monitor The LCD monitor has been preset at the factory with the Timing shown in the section "Appendix B" to achieve optimal display. You can adjust the display to the desired brightness and sharpness by following the instructions. Buttons EXIT Functions Exit the OSD (On-Screen Display). -- Adjust setting bars (i. e. , CONTRAST, BRIGHTNESS, etc. ) to decrease setting values of the OSD. Adjust setting bars ( i. e. , CONTRAST, BRIGHTNESS, etc. ) to increase setting values of the OSD. Green ­ Normal operation Amber ­ Power Management (i. e. , DPMS mode: reduces power consumption < 5W when receiving no horizontal and/or vertical sync signal) + Power LED light status display How to Use the OSD (On-Screen Display) The OSD (On-Screen Display) lets you easily adjust the various settings for your LCD Monitor to desired levels of performance. The OSD includes a main menu and various submenus. Operating Procedure The buttons on the upper left side of the Control Panel are used to navigate the OSD. Follow the sequence below to do the following: navigate the OSD menu item, go through the submenus, select a setting, save or cancel the setting, and finally exit the OSD item. 1. 6 Adjusting Monitor Display There are two ways to adjust the monitor screen: auto adjustment and manual adjustment Auto Adjustment 1. Make sure that your LCD monitor is not "CONTROLLOCKED" by pressing " " and "--" simultaneously. The "CONTROL LOCK" screen will disappear automatically or you may press "EXIT" to exit from the screen. Press either the " " or " " to display the OSD screen. Select "AUTO SETUP" of OSD screens by pressing the" " button for to "AUTO SETUP" . Press the "+" button while displaying the "AUTO SETUP" screen. The message "Auto Setup" displays, and auto adjustment of the monitor is completed in moments. Manual Adjustment 1. To perform manual adjustment of settings, follow the procedures outlined in the "Operating Procedure" section (previous page), and apply the procedures for settings described in the Menu Table (p. 10). 7 OSD Adjustment Lock This function is used to prevent inadvertent changing of monitor settings. All adjusted items (except "BRIGHTNESS") will be locked when this feature is used. Press the " " and "--" buttons simultaneously; the "CONTROL LOCK" screen is displayed. 2. [. . . ] When using the monitor over a prolonged period of time, a ten-minute-break per hour is recommended. 16 Special Notes On LCD Monitors The following conditions are normal with LCD monitors and do not indicate a problem. · When turning on the LCD monitor for the first time, the picture may not fit in the display area. (See the section, "Operating the Monitor" . ) · The screen may flicker during initial use. Turn off the power switch and then turn it on again; the flickering should disappear. [. . . ]