User manual MICROTEK GNC I SM9800XL 1201

[. . . ] ScanMaker 9800XL Installing and Getting Started Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unpacking the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Taking a Closer Look . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] System is FireWire-ready · For Macintosh users, your computer should have been equipped with a built-in FireWire port. This port should be designated with the FireWire symbol shown to the left. · For PC users, the FireWire card should be installed and work properly in your computer. System is Not FireWire-ready If your system is not FireWire-ready, you will need to install a FireWire card. For more details on how to install the FireWire card, please refer to the "FireWire Installation Guide" on a separate documentation included with your scanner package. Alternatively, you can use the USB or SCSI interface to connect your scanner. For FireWire-ready systems: Follow the steps below to make the FireWire connection. Plug the power cord into the back of the scanner, and plug the other end into a power source (power surge protector highly recommended). Make sure no other cable is connected to the scanner except the power cord at this point. 6 ScanMaker 9800XL Installing and Getting Started 2. Connect the scanner to your computer, using the provided FireWire cable. Connect one end of the FireWire cable to your computer's FireWire port, and connect the other end of the cable to the scanner's FireWire port. For Macintosh users The latest Macintosh computers (i. e. , G3, G4, etc. ) are equipped with a built-in FireWire port, usually labeled with the " " logo. For PC users 3. Turn the scanner's power switch to "On", and wait for the green light on the scanner's front panel to stop blinking and stay on steady. 4. Your system will detect the scanner automatically. ScanMaker 9800XL Installing and Getting Started 7 Using the SCSI cable Before connecting the scanner, check to see if your computer system has a built-in SCSI interface or an installed SCSI card. If you need help on installing the SCSI card, please refer to the "SCSI Installation Guide" on a separate documentation included with your scanner package, or refer to the documentation that came with the SCSI card. If the SCSI ID number 6 is used by another SCSI device, check which SCSI ID is free, and set the number to a free SCSI ID. Push the minus button (-) above the SCSI ID number to decrease the number; push the plus button (+) to increase the number. 3. Connect one end of the SCSI cable to your computer's SCSI port, and connect the other end of the cable to the scanner's SCSI port. For Macintosh users 8 ScanMaker 9800XL Installing and Getting Started For PC users 4. Set the scanner's terminator switch to the "ON" position. Note: If you have multiple devices on your SCSI chain, make sure the scanner is the last device on the chain and that the scanner is terminated (i. e. , scanner's terminator switch is set to ON). ScanMaker 9800XL Installing and Getting Started 9 5. Plug the power cord into the back of the scanner, and plug the other end into a power source (power surge protector highly recommended). 6. Turn the scanner's power switch to "On", and wait for the green light on the scanner's front panel to stop blinking and stay on steady. 7. Turn on your computer; the system will detect the scanner automatically. 10 ScanMaker 9800XL Installing and Getting Started Using the USB cable Before connecting the scanner, check to see if your computer system has a built-in USB port. The latest Macintosh computers (i. e. , G3, G4, etc. ) are equipped with a built-in USB port, and usually labeled with the USB " " logo. Plug the power cord into the back of the scanner, and plug the other end into a power source (power surge protector highly recommended). This will reflect colors consistent with the newly selected profile. 2. [. . . ] Set the appropriate parameters, click the Start Profiling button, then follow the screen instructions to generate your ICC profile. 6 5 4 3 2 1 0 Choose the scanner model you are currently using. Select "Reflective" Select the date code and target type to match your target ScanMaker 9800XL Installing and Getting Started 17 4. For details, refer to the help file of your Scanner ICC Profiler program. 5. When done, click the Close button to exit Scanner ICC Profiler program. Loading a profile Once the profile has been produced, follow the steps below to load the profile you just created. [. . . ]