User manual MICROTEK GNC I SM9700XL 0402

[. . . ] Microtek bears no responsibility for the unauthorized use of copyrighted materials. Installing the Scanner Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Connecting the Scanner toYour Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connecting using the SCSI cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connecting using the USB cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Once the scanner software installation is finished, remember to re-enable the virus protection software. For iMac users, please visit Apple's website at http://www. apple. com/imac/ to download and install any iMac updates you may require. ScanMaker 9700XL Installing and Getting Started 5 Connecting the Scanner to Your Computer The ScanMaker 9700XL comes with two built-in interfaces: USB and SCSI. You may choose any of the two interfaces to make the connection between the scanner and computer. (You should use only one interface at a time. ) Connecting using the SCSI cable Before connecting the scanner, check to see if your computer system has a built-in SCSI interface or an installed SCSI card. If you need help on installing the SCSI card, please refer to the "SCSI Installation Guide" on separate documentation included in your scanner package, or refer to the documentation that came with the SCSI card. If the SCSI ID number 6 is used by another SCSI device, check which SCSI ID is free, and set the number to a free SCSI ID. Push the minus button (-) above the SCSI ID number to decrease the number; push the plus button (+) to increase the number. 3. Connect one end of the SCSI cable to your computer's SCSI port, and connect the other end of the cable to the scanner's SCSI port. 6 ScanMaker 9700XL Installing and Getting Started For Macintosh users For PC users 4. Set the scanner's terminator switch to the "ON" position. Note: If you have multiple devices on your SCSI chain, make sure the scanner is the last device on the chain and that the scanner is terminated (i. e. , scanner's terminator switch is set to ON). ScanMaker 9700XL Installing and Getting Started 7 5. Plug the power cord into the back of the scanner, and plug the other end into a power source (power surge protector highly recommended). 6. Turn the scanner's power switch to "On", and wait for the green light on the scanner's front panel to stop blinking and stay on steady. 7. Turn on your computer; the system will detect the scanner automatically. 8 ScanMaker 9700XL Installing and Getting Started Connecting using the USB cable Before connecting the scanner, check to see if your computer system has a built-in USB port. The latest Macintosh computers (i. e. , G3, G4, etc. ) are equipped with a built-in USB port that is usually labeled with the USB " " logo. Plug the power cord into the back of the scanner, and plug the other end into a power source (power surge protector highly recommended). Make sure no other cable is connected to the scanner except the power cord at this point. 2. Connect one end of the USB cable to your computer's USB port, and connect the other end of the cable to the scanner's USB port. For Macintosh users USB port usually labeled with the " " logo. ScanMaker 9700XL Installing and Getting Started 9 For PC users 3. Turn the scanner's power switch to "On", and wait for the lights on the scanner's front panel to stop blinking and stay on steady. Your system will detect the scanner automatically. 10 ScanMaker 9700XL Installing and Getting Started Positioning Reflective Originals 1. Place the original to be scanned face down on the scanner's glass surface. Center the top of the original along the horizontal ruler on the scanner. If you are scanning a book or thick materials, lift the scanner lid out of its hinge sockets high enough to create room between the originals and the lid. 3. Lower the scanner lid. Note: To scan transparency materials (positive or negative films) with the ScanMaker 9700XL, you should have an optional Transparent Media Adapter (TMA1600) installed. For more details on the TMA1600, contact Microtek Customer Service. ScanMaker 9700XL Installing and Getting Started 11 Your First Scan 1. [. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party: Loi Han 16941 Keegan Avenue Carson, CA 90746 USA Telephone No: 1-310-687-5800 Fax No: 1-310-687-5950 Trade Name Model Number ScanMaker 9700XL MRS-2400A3 Tested to Comply With FCC Standards FOR HOME OR OFFICE USE Federal Communications Commission Interference Statement This equipment (Model: MRS-2400A3) has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ]