User manual MICROTEK FUNVIEW S350

[. . . ] STOP -> STOP -> PLAY: Play disc from the beginning STOP -> PLAY: Resume from the point where playing stopped. UP/DOWN/RIGHT/LEFT (1) Direction use: Navigate the OSD (2) Adjustment use: Increase/decrease the quality of video in BRIGHTNESS, TINT, COLOR, and CONTRAST. PIX (Picture Selection) Each time this button is pressed, the picture adjustment OSD cycles through selections for BRIGHTNESS, CONTRAST, COLOR, and TINT. Once the desired adjustment bar is displayed, use the RIGHT/ LEFT button to adjust the setting. [. . . ] There are 5 speed options to choose from, such as FF(Fast Forward). 19. REPEAT (Except VCD with PBC on) Repeat part or all of a chapter, title, track, or an entire disc. 21. Subtitle Change the subtitle language to another available language (only if the disc contains multiple subtitle languages). 24. This button takes effect only on DVDs that support frames with multiple angles. 25. Audio Change the audio language to another available language (only if the disc contains multiple audio languages). 26. MUTE Press this button to shut off the sound at the headphone station. Pressing the button again restores sound to the previously set Level. -14- General Operating Instructions Supplying the AC Power to the Unit Turning the unit ON or OFF 1. To turn on the system, slide the POWER switch on the right side of the unit to the position labeled "ON". To turn off the system, slide the POWER switch on the right side of the unit to the position labeled "OFF". To save power, slide the POWER switch to the position labeled "STANDBY". This can be done while you are listening to music or sound on the disc, and will turn off the LCD backlight to save energy. DC Plug AC Plug POWER Switch 1. Insert the DC plug into the "DC INPUT" jack on the right side of the unit. Attach the AC plug to the AC outlet. -15- Charging the Battery Pack CHARGE LED POWER Battery Pack POWER LED POWER Switch When the "POWER LED" starts to blink in red, the battery will stop supplying power to the system in 10 minutes. Please follow the steps below and refer to the diagram at the right-hand side. DC INPUT (1) Slide the POWER switch to the "OFF" position in the direction of arrow as indicated by the diagram on the right. (2) Connect the DC plug of the AC/DC adapter to the "DC INPUT" jack on the right side of the unit. (4) The "CHARGE LED" will turn to red to indicate that the unit is charging the attached battery pack. (5) The "CHARGE LED" will turn green after the battery is full. DC Plug AC Plug -16- Unloading the Battery Step 1: Press the points on the battery pack with your fingers, as indicated by the diagram above. Step 2: Keep pressing and pull the battery pack out in the direction indicated by the drawing above. Step 3: Slide the battery pack out, as shown in the diagram above. -17- DVD Basics To get the optimum use out of your DVD player, make sure you read this section completely. Loading and Playing Discs Before you load a disc, make sure that it is compatible with the player. Note that the following discs CANNOT be used with this player¡G Optical disc ¡E CD-1, CD-ROM, DVD-ROM Mini disc ¡E CDG(audio only , not graphics). Regional Coding Both the DVD player and disc are coded by regions. Other regional codes can't be played in this unit. Types of Discs your DVD will play DVD-Video: DVD contains video. CD-R/RW: A disc that contains audio files (for example, a CD-R with downloaded MP3 Files), MPEG, or JPEG files. Loading and Playing a Disc When you slide the POWER switch to the "ON" position. Slide the OPEN switch to right for lifting the front panel and put the disc printed-side up into the disc area. [. . . ] v Before putting on headphones always adjust the volume setting to the lowest position. v Do not put pressure on the screen. v Avoid touching or scratching the screen, as the screen may become dirty or damaged. Troubleshooting 1. IR Sensor Inoperative (1) Verify that the batteries in the remote are fresh. (3) Verify that the infrared transmitter is affixed over the sensor eye of the component to be controlled. [. . . ]