User manual MICROTEK CX6

[. . . ] User's Manual CX6 DLP Projector www. microtek. com Conference Projectors Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright September, 2004 Disclaimer The information in this document is subject to change without notice. The manufacturer makes no repr esentations or warranties with respect to the contents hereof and specifically disclaims any im plied warranties of merchantability or fitness for any particular purpose. [. . . ] Be sure cables are not in the way or can cause the projector to be knocked over. 1. To raise the level of the projector, lift the projector [A] and press the height-adjuster buttons [B]. The height-adjusters drop down [C]. 2. To lower the level of the projector, press the height-adjuster buttons and push down on the top of the projector. ­ 14 ­ Se tu p an d O pe rattiion Se u n O Adjust the Zoom, Focus and Keystone 1. Use the Image -zoom control (on the projector only) to resize the projected im age and screen size A . 2. Use the Image -focus control (on the projector only) to sharpen the projected image A B 3. Use the Keystone buttons (on the projector or the remote control) to correct image-trapezoid (wider top or bottom) effect. The keystone control appears on the display. ­ 15 ­ D LP Projje c tor -- U se r Manu al D Pr e c r se r Manu Adjusting the Volume 1. Press the Volume +/- but tons on the projector or the remote control. The volume control appears on the display. 2. Use the Volume +/- but tons to adjust the level. 3. 4. Press the Mute button (on the remote control only) to turn off the volume. Press Volume +/- or Mute on the remote control to turn off mute. ­ 16 ­ ON-SCREEN DISPLAY MENU SETTINGS On-Screen Display Menu Controls The projector has an On-Screen Display (OSD) that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the remote control and on the projector. D LP Projje c tor -- U se r Manu al D Pr e c r se r Manu Setting the OSD Language You may want to reference the OSD on your projector while reading this section. Press the Menu button twice to close the OSD. ­ 18 ­ On--Screen Diispl ay Men u Settti n gs O cr p ay Men en Main Menu Press the Menu button to open the OSD menu. Press to change values for settings, and then press Enter to confirm the new setting. ITEM Brightness Contrast Sharpness Color Temperature Color Satur ation Color Tint Gamma Press Press Press D ESCRIPTION to adjust the brightness. (Range: 0 --100) to adjust the display sharpness (Range: 1-5) DEFAULT 50 50 3 Normal 50 50 Press to adjust the video tint/hue. (Range: Cool/Normal/Warm) Press Press Press to adjust the video saturation. Input PC MAC Video Chart B&W Gamma 2. 2 1. 8 2. 4 2. 2 2. 4 Brightness High High Low Low High PC Color Space Press to adjust the color space. (Range: Auto -- RGB -- YPbPr --YCbCr) Resets all Main items settings except Color Saturation to default values Auto - Reset ­ 19 ­ D LP Projje c tor -- U se r Manu al D Pr e c r se r Manu Main Menu Items Supported for Each Input Source Depending on the video source not all items in the OSD are available. Items that are available for each input source are marked with "X". Function Brightness Contrast Sharpness Color Temperature Color Saturation Color Tint Gamma X X RGB X X X X DVI X X X X Component Video X X X X X X X Composite V ideo X X X X X X X S-Video X X X X X X X ­ 20 ­ On--Screen Diispl ay Men u Settti n gs O cr p ay Men en Setup Menu Press the Menu button to open the OSD menu. Press to change values for settings, and then press Enter to confirm the new setting. ITEM Horizontal Position Vertical Position Press DESCRIPTION to move the image left or right. (Range: 0 --100) DEFAULT 50 Press to move the image up or down. (Range: 0 --100) 50 ­ 21 ­ D LP Projje c tor -- U se r Manu al D Pr e c r se r Manu ITEM Keystone DESCRIPTION Press to correct distortion of the projected image. (Range: -50 --50) Press to toggle between the 4:3 standard format and 16:9 High Definition TV (HDTV) format. DEFAULT 0 Aspect Ratio Advance Feature Reset 4:3 Resets Keystone and Aspect Ratio to default values Setup Menu Items Supported for Each Input Source Depending on the video source not all items in the OSD are available. Items that are available for each input source are marked with "X". Function Horizontal Position Vertical Position Keystone RGB X X X X X X X DVI Component Video Composite V ideo S-Video ­ 22 ­ On--Screen Diispl ay Men u Settti n gs O cr p ay Men en Config Menu Press the Menu button to open the OSD menu. Press to change values for settings, and then pr ess Enter to confirm the new setting. ITEM Blank Screen Auto Source Auto Power Off Volume Menu Position Menu Display Translucent Menu Reset DESCRIPTION Press to select a background color for blank screen (Range: Black ­ Red-- Green -- Blue --White) Press to enable or disable automatic source detection (Range: On -- Off) Press to enable or disable automatic shut-down of lamp after 10 mi n utes of inactivity (Range: On --Off) Press to adjust the audio volume level (Range: 0 - 10) DEFAULT Blue On Off 5 Center 15 Off Press to position the OSD on screen (Range: Left --Right --Center -- Down --Up) Press to determine the timeout delay of the OSD (Range: 10 - 20 sec. ) Press to set menu screen translucency (Range: On -- Off) Resets all Config screen items to default values ­ 23 ­ D LP Projje c tor -- U se r Manu al D Pr e c r se r Manu Utility Menu Press the Menu button to open the OSD menu. Press to change values for settings, and then press Enter to confirm the new setting. ITEM Video Type Video AGC D ESCRIPTION Press to select the video standard. (Range: Auto --NTSC --PAL -- SECAM) Press to enable or disable aut omatic gain control for the video source. [. . . ] To ensure the problem is not caused by a connected PC's video card, connect to another computer. Problem: The image is flat with no contrast 1. Adjust the Contrast setting on the Main menu of the OSD. Problem: The color of the projected image does not match the source image. 1. Adjust the Color Temperature a n d Gamma settings on the Main menu of the OSD. Lamp Problems Problem: There is no light from the projector 1. Ensure the power source is good by testing with another electrical device. [. . . ]