User manual MICROTEK C997SD

[. . . ] And with its low power consumption, the LCD Monitor helps you reduce your power bill. Unpacking Before you unpack your LCD Monitor, prepare a suitable workspace for your LCD Monitor and computer. Even though the LCD Monitor uses very little power, you should put it in a location which allows sufficient airflow to ensure that the LCD Monitor and your computer do not overheat. Set up your LCD Monitor so that the panel is not facing a window where sunlight often comes in. The glare caused by sunlight reflecting off of the LCD Monitor's screen will make it difficult to use the Monitor for viewing. Note: Using a computer for an extended period of time with a poor workstation set-up and incorrect working habits can cause health problems. [. . . ] Please refer to the next chapter for details. Power Management System The LCD Monitor complies with the VESA DPMS (version 1. 0p) power management proposal. The VESA DPMS proposal provides four phases of power-saving modes by detecting the horizontal or vertical sync signal. When the LCD Monitor is in power-saving mode or detects an incorrect timing, the Monitor screen will go blank and the power LED indicator will start to blink. The Display Controls The LCD Monitor's Display Controls This chapter covers the LCD Monitor's On Screen Display (OSD). Using the OSD, you can adjust the contrast, brightness, display position, display clarity, and color temperature. Please read this chapter carefully to get the most out of your LCD Monitor. Adjusting the Monitor's Display The LCD Monitor features an intuitive, menu-driven, On-Screen Display (OSD). If the PC is in a power-saving mode, or is powered off, the OSD is inaccessible. Take note of the following: Use the Function buttons to access the OSD and scroll through the various OSD items. The Function buttons can also be used at any time to move through a palette of menu items (such as suboptions within an OSD function). · With a particular OSD function selected (such as Monitor Control), use the Adjustment buttons to access the suboptions (e. g. , H-Position or V-Position under Monitor Control). The Adjustment buttons can also be used at any time to change values for a particular setting, or to exit a suboption. Please refer to Figure 1-1 for the location of the Function and Adjustment options on your LCD Monitor. · OSD Main Menu To access the OSD main menu, press the OSD Menu button (the first Function button on your LCD Monitor). To scroll between the OSD main menu options, use the second Function button on your LCD Monitor. Analog or digital mode is automatically detected by the Monitor. A. Analog Mode Each main menu and submenu item is covered below. Pressing the OSD Menu button causes the following screen to appear (an example): Figure 2-1: The OSD Main Menu The Monitor Control Option The Monitor Control option allows you to adjust the display characteristics of the LCD Monitor. H-POSITION: Use this option to move the LCD monitor's display left or right on a horizontal plane. V- POSITION: Use this option to move the LCD monitor's display up or down on a vertical plane. PHASE: Use this option to adjust the focus and clarity of the display. RESET: Use this option to reset the H- Position, VPosition, Phase and Clock parameters. PORT-SELECT: Use this option to change input between the VGA port and DVI digital port. EXIT: Use this option to exit the Monitor Control submenu. The OSD Control option lets you adjust the position of the OSD on the screen. OSD-H-POSITION: Use this option to change the position of the OSD on a horizontal plane. OSD-V- POSITION: Use this option to change the position of the OSD on a vertical plane. EXIT: Use this option to exit the OSD Control submenu. The Graphic Control option lets you make adjustments that effect the contrast, brightness and color of the LCD monitor's display. [. . . ] Press the upper Function Control button (refer to Chapter 2) once and then press either the upper or lower Adjustment Control button several times. If there is still no display, press the other Adjustment Control button several times. If step 2 does not work, connect your PC system to another external CRT. If your PC System functions properly with a CRT Monitor but it does not function with the LCD Monitor, and the LCD Monitor's power LED is blinking, the output timing of the PC's VGA card may be out of the LCD's synchronous range. [. . . ]