User manual MICROTEK C893

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1 18" LCD monitor Reorient or relocate the receiving antenna. · Increase the separation between the equipment and the receiver. [. . . ] If any of the following occurs, immediately unplug your monitor and call an authorized technician. Liquid has been spilled onto the monitor, or it has been exposed to rain. If you lose the power cord, you must purchase a power cord of the same type and configuration. l Japan : VCTF type, 3 wires or with ground-wire, T-mark approval is required. 3 18" LCD monitor l l U. S. : VW-1; 18AWG X 3C; SVT with national approval as UL and/or CSA approval/number(s) Europe : VDE / Ö VE and/or KEMA approval; H05VV-F, 3G, 0. 75mm , or equivalent. 2 The power cord should bear the name of the manufacturer and state the type of cord that it is. 4 18" LCD monitor CHAPTER 1 INTRODUCTION BEFORE INSTALLING YOUR MONITOR Read this manual carefully. If a problem occurs, contact the manufacturer's authorized service center. ABOUT YOUR MONITOR This monitor is a microprocessor-controlled, color monitor that uses a TFT LCD panel. The monitor conforms to EPA Energy Star and VESA DPMS (Display Power Management Signaling) power management standards. RGB MODE This monitor is equipped with a microprocessor that identifies your computer 's video mode and allows you to adjust the setting. 5 18" LCD monitor FACTORY-PRESET MODES Table 1 shows standard video mode settings that have been pre-adjusted at the factory for accurate video display. Factory-Preset Modes Mode NEC VGA Resolution 640x400 640x350 720x400 640x480 640x480 640x480 800x600 800x600 800x600 800x600 1024x768 1024x768 1024x768 1280x1024 1280x1024 640x480 832x624 1024x768 1024x768 H-Freq. (KHz) 24. 83 31. 47 31. 47 31. 47 37. 86 37. 5 35. 16 37. 88 48. 08 46. 87 48. 36 56. 47 60 63. 98 80 35 49. 7 48. 78 60. 241 V-Freq(Hz) 56. 4 70 70 60 72 75 56. 3 60. 3 72. 2 75 60 70 75 60 75 66. 7 74. 55 60 74. 927 SVGA XGA SXGA Macintosh 6 18" LCD monitor SPECIFICATIONS l 18" LCD Monitor Overall Dimension (HxWxD): Shipping Weight (G/W): Effective Display area (H/V): Display colors: Scan Frequencies: Horizontal Vertical Viewing Angle Contrast Ratio Response time ( Tr + Tf ) Native Resolution Pixel pitch: Power: Input Consumption Video Connector: RGB Signals: Video Sync Display Data Channel: Compatibility 426 x 444 x 215 mm 11Kg 359. 04 x 287. 23 mm 16. 7M colors 31. 47KHz to 80KHz 60Hz to 75Hz 160 /160 degree H/V 400:1 30ms 1280x1024(SXGA) 0. 279x0. 279 mm 110-240VAC (auto-sensing) Frequency: 48-62Hz 48 Watts maximum (ON) 1 Watt (Power-saving OFF mode) 15-pin Mini D-sub (Standard) Analog RGB 0. 7Vp-p/75 Separate VESA DDC 1/2B 7 18" LCD monitor Control Type: Compatibility: Environmental Limits: Operating Temp. Operating Humidity Storage Humidity Agency Approval EMI Energy Saving Safety Digital IBM and compatibles, Apple Macintosh, NEC 32°F to 113°F ( 0°C to 45°C ) -4°F to 140°F ( -20°C to 60°C ) 10% to 85% without condensation 10% to 95% without condensation FCC-B EPA energy star UL 8 18" LCD monitor CHAPTER 2 INSTALLING THE MONIT OR The monitor is equipped with an auto sensing power supply for voltage ranges from 110~240VAC, 60/50Hz. Confirm the line voltage designation on the rear panel of the monitor. FOLLOW THESE STEPS T O INSTALL THE MONITOR 1. Before you connect the cables, make sure that the monitor and the computers are both turned off. Plug one end of the 15-pin signal cable to the monitor and the other end to the video signal connector at the rear of the system. Otherwise the screen will be abnormal and the LED light will be yellow instead of the normal green color. 4. 9 18" LCD monitor 10 18" LCD monitor CONTROL FUNCTIONS The Monitor control functions are located on the lower right side of the front part of the monitor, just below the glass. The control functions are shown in the figure below and described in the following paragraphs. The control key description: 1. MENU : Activates the OSD (on-screen display) 11 18" LCD monitor Description 1. We recommend turning your system power on first before turning on the monitor 2. - & + : Decrease/increase The two keys work to decrease or increase the value of the selected item. Sel : Select key This key is used to select the items or functions to be adjusted. Menu Press the Menu key to activate the OSD (on-screen display) screen; this is a toggle key. [. . . ] If your PC System functions properly with a CRT Monitor but it does not function with the LCD Monitor, and the LCD Monitor's power LED is blinking, the output timing of the PC's VGA card may be out of the LCD's synchronous range. Please change to an alternate mode listed in table 1 on page 2 or replace the VGA card and repeat steps 1 and 2. If the PC doesn't function with the CRT monitor neither, check BIOS to see if there is a dual scan setting under the display mode item. If there is still no display, then there may be a problem with your system. [. . . ]