User manual MICROTEK C593

[. . . ] 1 Adjustment Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Auto-Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 RGB Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Contrast Value Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] These limits are designed to provide proper protection against harmful interference to a residential installation. Harmful interference to radio communication may result if it is not properly installed and used. However, there is no guarantee that interference will not occur in a particular installation. If this monitor does cause serious interference to radio or television reception, resetting the monitor may resolve the problem. Moreover, users are encouraged to correct interference by doing one or more of the following: · · · · Reorient or relocate the receiving antenna. Connect the monitor into an outlet on a circuit different from that to which the receiver is connected. Consult your local dealer or a qualified technician. FCC Warning: To assure a continued FCC compliance, a user must use a grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized changes or modifications to this monitor will void the user's authority to operate this device. power cord must be used to meet the emission level limits. EMI Certification The Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulation. Cet appareil numerique de class B respecte toutes les exigences du Reglement sur Ic materiel brouilleur du Canada. iv Safety Precautions This monitor is manufactured and tested on the ground principle that a user's safety comes first. However, improper use or installation may not only damage the monitor but endanger the user as well. As a safety precaution, go over the following WARNINGS carefully before installation, and keep this guide handy. Warnings: · This monitor should be operated only at the correct power sources indicated on the label at the rear end of the monitor. If you are unsure of the power supply in your residence, consult your local dealer or Power Company. Do not try to repair the monitor yourself, as it contains no user-serviceable parts. There are high-voltage parts inside that may cause electric shock to human bodies, even when the power cord is disconnected. Unplug the monitor immediately if it gets wet, and consult your service technician. Apply non-ammonia-based cleaner onto the cloth, not directly onto the glass screen. Keep the monitor away from magnetic objects, motors, TV sets, and transformers. For PLUG CABLE EQUIPMENT, the socket outlet should be installed near the equipment and should be easily accessible. · · · · · · · · v Care and Maintenance Care · · · · Avoid exposing your monitor directly to sunlight or other heat sources. Make certain that your monitor is installed in a clean and moisture-free area. Keep your monitor away from magnets, motors, transformers, speakers, and TV sets. SafetyTips · · If smoke, abnormal noise or odor comes out of your monitor, switch off the power immediately and call your service center. [. . . ] The screen below will appear. 1024X768 Auto-Balance CONTRAST RED GREEN BLUE BALANCE RED GREEN BLUE 75 Hz/60 KHz 20 18 19 49 50 26 VERSION XGAD9B11-5100 Contrast Value Adjustment Use the selection key to select the CONTRAST field, then press - & + to get the best contrast optimization. You can adjust R, G, B simultaneously or adjust each Red, Green, and Blue channel separately. You can also use this field to change purity of the RGB levels. Color Balance Use the selection key to select the COLOR BALANCE field, then press - & + to get the best color balance effect or to separately set the RGB color values. The easiest way to adjust the contrast and color balance setting is to use auto-balance. 3 Geometry Adjustment Use the selection key to select the icon, then press - & +. [. . . ]