User manual MICROTEK ARTIXSCAN 1100

[. . . ] ArtixScan 1100 Hardware User's Guide English English Copyright © 1999 Microtek Lab, Inc. All rights reserved. 3715 Doolittle Drive, Redondo Beach, CA 90278-1226 Sales: 800-654-4160 Internet: http://www. microtekusa. com Tech Support Web Page: http://www. support. microtek. com Microtek International, Inc. 6, Industry East Road 3 Science Based Industrial Park Hsinchu 30077, Taiwan, R. O. C. Tel: 886-3-5772155 Fax: 886-3-5772598 Internet: http://www. microtek. com Microtek Europe BV Max Euwelaan 68 NL - 3062 MA Rotterdam The Netherlands Tel: 31-10-242-5688 Fax: 31-10-242-5699 Internet: http://www. microtek. nl Contents 1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Click Next and select No for "Do you want Windows to search for your new hardware?". When the settings are all correct, click OK to save the modifications. The dialog box should now show the correct Interrupt Request, Memory Range, and Input/ Output address settings. Select Adaptec on the left and "Adaptec AIC-7850 PCI SCSI Controller" on the right. When the "Add New Hardware Wizard" dialog box appears, click Finish. No conflicts found If you are asked to shut down your computer, select No, then click Close. Click Yes and restart your computer. 14 ArtixScan 1100 Hardware User's Guide 7. When installation is complete, Windows will ask if you wish to shut down your computer. Double-click on the System icon in Control Panel and select Device Manager from the top. 10. Double-click on "SCSI controllers" to check whether conflict happens. When the settings are all correct, click OK to save the modifications. The dialog box should now show the correct Interrupt Request, Memory Range, and Input/ Output address settings. If you are asked to shut down your computer, select No, then click Close. Click Yes and restart your computer. ArtixScan 1100 Hardware User's Guide 15 English English 5 Installation under Windows NT 4. 0 1. Card installation on Windows NT 4. 0 is the same as that under Windows 98 / 95. 6. Troubleshooting After installing the interface card in your computer and connecting the scanner, you may find yourself unable to use the scanner. This is usually due to any of the situations described below: Situation A Your interface card is not properly seated 2. Installing the Windows NT driver a) Start your computer, and log in as Administrator. Note: You must be logged in as Administrator in order to install the scanner software components and use the scanner. In Windows, go to Start, Settings, then double-click on Control Panel, and doubleclick on the SCSI Adapters icon. Select the Drivers tab in the SCSI Controllers dialog box, and click on the Add button. From the list of drivers that appear, select Adaptec for manufacturers on the left, and Adaptec AIC-78xx PCI SCSI Controller on the right. You may be asked to insert your Windows NT CD-ROM at this point; do so. Click Yes to do so. in the PCI card slot on your computer. Situation B The driver for the interface card is not b) properly installed on your computer. [. . . ] You should enable this option if you wish to: · · · Minimize detail in the shadow areas of the image; Make the shadow areas of an image darker; or Reduce the appearance of noise in the shadow areas. 6. Start Calibration: This button starts the calibration process by displaying the calibration window and guides you through the process to create a customized scanner ICC profile. Scanner Model: This option lets you select the scanner to be calibrated. If a particular media is not supported, that media will not appear on the list. Target type: This option lets you select the Target Description File (TDF) that matches your Q-60E3 calibration target being used for calibration. [. . . ]