User manual MICROTEK 710S

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. [. . . ] Liquid has been spilled onto the monitor, or it has been exposed to rain. If you lose the power cord, you must purchase a power cord of the same type and configuration. Japan GVCTF type, 3 wires or with ground-wire; T-mark approval is required. GVW-1; 18AWG X 3C; SVT with national approval as UL and/or CSA approval/number(s) Europe GVDE/ÖVE and/or KEMA approval; H05VV-F 3G, 0. 75mm2, or , equivalent. The power cord should bear the name of the manufacturer and state the type of cord that it is. 2. · · · v Introduction Before installing your monitor Read this manual carefully. If a problem occurs, contact the manufacturer's authorized service center. About your monitor This monitor is a microprocessor-controlled color monitor that uses a TFT LCD panel. The monitor conforms to EPA Energy Star and VESA DPMS (Display Power Management Signaling) power management standards. RGB Mode This monitor is equipped with a microprocessor that identifies your computer's video mode and allows you to adjust the setting. 1 Factory-preset Modes Table 1 shows standard video mode setting that has been pre-adjusted at the factory for accurate video display. Factory-preset Modes Mode NEC VGA Resolution 640 x 400 640 x 350 720 x 400 640 x 480 640 x 480 640 x 480 SVGA 800 x 600 800 x 600 800 x 600 800 x 600 XGA 1024 x 768 1024 x 768 1024 x 768 SXGA 1280 x 1024 1280 x 1024 Macintosh 640 x 480 832 x 624 1024 x 768 1024 x 768 H-Freq. (KHz) 24. 83 31. 47 31. 47 31. 47 37. 86 37. 5 35. 16 37. 88 48. 08 46. 87 48. 36 56. 47 60 63. 98 80 35 49. 7 48. 78 60. 241 V-Freq (Hz) 56. 4 70 70 60 72 75 56. 3 60. 3 72. 2 75 60 70 75 60 75 66. 7 74. 55 60 74. 927 2 Specifications Overall Dimensions (H x W x D): 16. 5 x 16. 4 x 6. 5 in. (337. 92 x 270. 34 mm) 100 x 100mm (VESA standard) 16 million colors Gross / Net Weight Effective Display area (H/V): Wall Mount Display colors: Scan Frequencies: Horizontal Vertical Number of Pixels: Pixel pitch: Picture Tube: Power: Input Consumption 31. 47K to 80KHz 60Hz to 75Hz 1280x1024 pixels 0. 264 mm 17" TFT LCD panel 110~240 VAC (auto-sensing) Frequency: 48-62Hz 45Watts maximum (on) 1 Watt (Power saving off mode) 15-pin Mini D-sub (Standard) 1 (stereo input) 2 Video Connector Audio connector Speaker: RGB Signals: Video Sync Display Data Channel: Compatibility 3 Analog RGB 0. 7Vp-p/75W Separate VESA DDC 1/2B Operations User Controls On/Off Power Button Auto-adjustment, Brightness, Menu/Enter and & button On Screen Display, Contrast, Brightness Adjustment, H-position, V-position, Color temperature, Auto Adjustment Digital OSD (On-Screen-Display) IBM and compatibles, Apple Macintosh, NEC Control Type: Compatibility: Environmental Limits: Operating Temp. Operating Humidity Storage Humidity Agency Approval EMI Energy Saving Safety 32° to 104°F ( 0° to 40°C) -4° to 140°F (-20° to 60°C) 10 to 85% without Condensation 10 to 95% without Condensation FCC, CE EPA energy star, VESA DPMS UL/CUL, CB, TUV, BSMI 4 Installing the Monitor This monitor is equipped with an auto sensing power supply for voltage ranging from 110~240VAC, 60/50Hz. Confirm the line voltage designation on the rear panel of the monitor. To install the monitor, follow these steps: 1. Before you connect the cables, make sure that the monitor and the system unit power switches are OFF. Plug one end of the 15-pin signal cable to the monitor and the other end to the video signal connector at the rear of the system. Otherwise, the screen will be abnormal and the LED light will flash yellow (and not the normal green color). Connect the power cord on the AC outlet as shown below. 2 3 2. 3. While pressing on the slider with one hand, use the other hand to bring the LCD panel down until it is on an even level with the VESA mount. Locate the holes for mounting and affix the monitor as desired. 6 Control Functions The control functions of the monitor are located on a dial in the lower center portion of the front panel. They are shown in the figure below and described in the following paragraphs. & : Power Switch : Cursor up/down or Decrement /Incremental; or Brightness Up/Down (hot key) 3. Auto : Menu/ Enter : Auto adjustment (hot key) Note: A hot key indicates that a particular function will work without the need to activate the On-screen display (OSD) menu. 7 1. : Power switch Use the power switch to turn power ON or OFF. [. . . ] Make sure that the power indicator on the LCD Monitor is lit, all connections are secure, and the system is running on the correct timing. Press the upper Function Control button once and then press either the upper or lower Adjustment Control button several times. If there is still no display, press the other Adjustment Control button several times. If step 2 does not work, connect your PC system to another external CRT. [. . . ]