User manual MICROTEK 211SD

[. . . ] Connect the equipment into an outlet different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit. The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. i CE mark for Class B ITE (Following European standard EN55022/ 1998; EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions 219-20-990423 A ii Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 9 Supported Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 iii Introduction Congratulations on the purchase of your new Microtek LCD monitor!With a 21" TFT active matrix color crystal display and offering a maximum resolution of 1024 x 768 pixels, your Microtek 21" LCD monitor offers sharp and vibrant color display with low radiation emission. And with its low power consumption, the monitor helps you reduce your power bill as well. Product Features · 21" high-contrast TFT color Liquid Crystal Display · Supports XGA resolution of 1024 x 768 pixels · VESA PMS-compliant power saving: Automatically powers down the monitor after a defined period of inactivity · Compatible with Windows 95/98/2000/XP and Macintosh · Easy-to-use OSD (On-Screen Display) · Plug & Play: Conforms to VESA standards and supports DDC1/2B specifications · Multiscan functions of XGA 1024 x 768, SVGA 800 x 600, VGA 640 x 480 and 720 x 350 for perfect graphics performance · Includes built-in speakers 1 Unpacking Before unpacking your LCD monitor, prepare a stable, level, and clean surface near a wall outlet for your LCD monitor. Set the LCD monitor box in an upright position and open from the top of the box before removing the right/left cushions. Check to see that you have the following accessories shown below: · · · · · · LCD monitor Power cord 15-pin D-sub signal cable DVI cable Audio cable User Guide Note: Remember to save your original box and packaging material in case you need to transport or ship the monitor. If you have to return your unit for service and the original packaging has been discarded, please contact your dealer or nearest service center for advice or replacement of packaging. Precautions · Read all of these warnings and save the manual for later use. · Do not insert sharp objects or spill liquid into the LCD monitor through the cabinet slots; this may cause accidental fire, electric shock or failure. · Disconnect the power plug from the AC outlet if you are not going to use the monitor for an extended period of time. · Do not attempt to service this product yourself, as opening or removing the cover may expose you to dangerous voltage points or other risks. 2 · Do not touch the screen directly with your fingers as you may damage the screen, and oil from your skin is difficult to remove. · Do not apply pressure to the screen, as the screen is very delicate. · Keep the monitor away from extremely hot, cold or humid places. · Do not place the monitor directly under sunlight, in dusty surroundings, or near equipment which may generate strong magnetic fields. Cleaning Warning: If you drop any material or liquid such as water onto the monitor when cleaning, unplug the power cable immediately and contact your dealer or the nearest service center. Caution: · For safety reasons, turn off the power switch and unplug the monitor before cleaning. · Never use any of the following solvents on the LCD monitor: Thinner; spray-type cleaners; benzene; wax; abrasive cleaners; and acid or alkaline solvents. Such harsh chemicals may cause damage to the cabinet and the LCD screen. · Rubbing the cabinet with products made of rubber or plastic for prolonged periods may cause degeneration or loss of paint on the cabinet. [. . . ] Pressing the OSD Menu button causes the screen below (Figure 4) to appear. Select EXIT and press the OSD Menu button when finished adjusting. Figure-4: The OSD Main Menu 7 The Menu Table Main Menu BRIGHTNESS CONTRAST V-POSITION H-POSITION PITCH Submenu Function Adjusts the level of brightness and darkness. Automatically fixes, centers and fine-tunes the video signal to eleminate noise and distortion. Adjusts the colors in the LCD monitor to a warmer or cooler shade, depending on the selected color temperature. [. . . ]