User manual METRONIC TOUCHBOX 4

[. . . ] Digital Satellite Receiver Réf : 441327-4 3500 channels Parental lock 2 scarts 16/9 Compatible DiSEqC 1. 2 VCR / LNB DEMO TV 100-250V~ 50/60Hz 14W L/G R/D VIDEO AUDIO MET712 IMPORTANT NOTICE ! The inside of your Touch Box 4 contains components submitted to high tension. In general, audio video products are not related to the earth so you can actually feel electric waves (which are not dangerous) by touching the two products simultaneously (or one product and the antenna cable). We advise that you plug the products in the sector after having made all the connections. The box must never be exposed to water, even water splashing, and you must never leave objects filled with liquid, such as vases, on top of the box. [. . . ] 2C or 2B Telecom = national channels in clear analogue), you will only have access to a few digital channels. We therefore advise you to install another antenna in order to keep receiving national channels in analogue and to watch digital channels as well. As the terminal is unplugged, directly connect the LNB to the LNB input of the terminal. Switch on the TV, plug the terminal to the sector, and `No signal' should appear on your screen. Press `OK' and the list of all pre-programmed channels should appear. B Connecting with a motorised DiSEqC 1. 2 already wedged If you have a motorised DiSEqC 1. 2 already installed, each satellite position should already be correctly programmed in the motor, which spots a satellite as a number. The notice of your previous demodulator should indicate the numbering used. If this is the case, it will be very easy for you to set up the Touch BOX 4. If you do not have access to this information, you should use the one following : Atlantic Bird 3 Hot Bird Astra 19 Eutlesat W2 Eutlesat W3 Astra 28 Sirius 2 Hispasat 30. 0 Turk 1C 42. 0 1 79 331 475 489 583 785 802 834 · Connect cables as shown on image 18 (below). · For each channel, go to the reference channel and enter the correct satellite number. The motor should automatically go to the right position, which you would see represented in the high quality bar (see picture below). 18 VCR / LNB DEMO TV 100-250V~ 50/60Hz 14W L/G R/D VIDEO AUDIO 20 info@metronic. com 6 A Installing on more than one satellite Installing on two satellites The case of Astra + HotBird has been discussed in Chapter 3 (monobloc). In this case, install a connector at each input (Tone Burst or DiSEqC 1. 0). Astra Atlantic Bird 3 1 2 Commutateur DiSEqC 1. 0 VCR / LNB DEMO TV 100-250V~ 50/60Hz 14W L/G R/D VIDEO AUDIO Astra = 1 Atlantic Bird 3 = 2 B Installing on three satellites If you do not have a motorised installation, you might wish to get 3 satellites (i. e. Atlantic Bird 3, Astra and HotBird). Astra + HotBird 2 LNB sur support bi-tête Atlantic Bird 3 1 2 3 VCR / LNB DEMO TV 100-250V~ 50/60Hz 14W L/G R/D VIDEO AUDIO DiSEqC 1. 0 HotBird = 1 Astra = 2 Atlantic Bird 3 = 3 Please be aware that it will not be possible to bring even one cable down if Astra and Hotbird are received by a monobloc. 21 info@metronic. com 7 1 2 3 4 Remote description 2 14 1 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Digital buttons. In normal use, they will allow you to enter the channel number you wish to view. `ON / OFF' button: allows you to set the terminal on standby or switch it on. `MENU' button: allows you to enter the main menu or to come back to the previous menu. You can also use these buttons to view the following (4) or previous (3) page in the long listings. `OK' button: allows you to list all channels and to validate in all menus. `EXIT' button: allows you to go back to the channel you were watching. `EPG' (Electronic Programs Guide) button: allows you to view the current program as well as the following ones when this information is transmitted by the channel. on Euronews on HotBird), this allows you choose the language of the program. `MUTE' button: by pressing this once stop the sound, and by pressing it again the sound will come back to normal. `INFO' button: allows you to view the technical parameters of the channel you are currently watching as well as the signal level. [. . . ] For your information, an operator can transmit a crypted channel whilst sending signals to your terminal to make it think that this channel is clear. Simply reset it · Why is my motor not running its full course anymore?You must ensure that the electronic nuts are positioned at the same place as the mechanic nuts (see chapter 4N). · Where can I find out which channels I can view on each satellite? [. . . ]