User manual METRONIC TOUCHBOX 2

[. . . ] Digital Satellite Receiver 3500 channels Parental Control 2 Scarts DiSEqC 1. 2 Timer SIGNAL MET447 CAUTION Your TouchBOX 2 has ventilation slots. These slots must not be obstructed, even partially, in order to ensure proper ventilation. The lifetime and normal functioning of your device depends on these factors. Installation in premises which are confined or subject to temperature or dampness changes (sheds, attics, cellars, tiny rooms, dry risers etc. ) may cause an overheating of the device or a premature ageing resulting in failures that are not covered by the guarantee. [. . . ] · On the line Limit set, choose East Limit and validate by OK. 5 - Connection on a fixed satellite dish already aligned on a satellite The receiver being disconnected from power supply, connect directly the LNB to the LNB receiver input. Connect a scart lead from the television to the receiver TV output scart socket. For the moment, do not connect any other standard appliance on the receiver DEMO output. Check in the list of the pre programmed channels at the end of the user manual. You can select and visualize the channels of this satellite towards which you are pointing. @Notes : if your satellite dish is currently pointed towards Atlantic Bird 3 (ex Telecom 2C = French national analogue channel in Free To Air), you will not have access to any digital channels. We then advise you to install another satellite dish to keep receiving the French national channels in analogue and watch others channels in digital. 24 www. metronic. com 6 - Connexion on a bi-head system Astra 19, 2° + Hotbird already aligned Remarks : this paragraph goes as well for Monoblocs. It is useful to know on which inputs of the switch the heads Astra and Hotbird are connected. If you do not know it and that the installation is difficult to reach, test the 2 possible combinations: Astra on A (or 1) and HotBird on B (or 2) or the opposite. To program your receiver, follow the instructions from paragraph 3B page 12. Caution: you should not touch the satellite dish adjustments nor to the switch, it is only necessary to program your digital receiver. schema monobloc DiSEqC switch1. 0 or Tone Burst DiSEqC1. 2 DiSEqC1. 2 13/18 V 500 mA DEMO LNB TV VCR / S/PDIF 13/18 V 500 mA DEMO LNB TV VCR / S/PDIF TouchBOX2 back Coaxial cable Scart lead www. metronic. com 25 7 - Connection on a motorised DiSEqC 1. 2 already aligned Connect the cables and the leads as indicated on the figures below. When 2 satellite receivers (a digital and an analogue receiver for example) control the same motor, it is important that each one of them give the same number to a given satellite. For an easiest installation of your new digital receiver, locate the classification of the satellites used by your analogue receiver. If your motor and your receiver have never been used before, use the number that you wish for each satellite. OU DiSEqC1. 2 13/18 V 500 mA DEMO LNB TV VCR / S/PDIF TouchBOX2 back Arrière Analogique DiSEqC1. 2 13/18 V 500 mA DEMO LNB TV VCR / S/PDIF TouchBOX2 back Arrière Analogique Coaxial cable Scart lead figure 5 Coaxial cable Scart lead If you do not have an analogue demodulator, connect directly the receiver to the television. For each satellite you want to receive in digital, it is necessary to proceed as follows: Example on HotBird · Go in MENU / Installation / Antenna type. · On the line LNB dish, choose Moved with the key 34 26 www. metronic. com For each satellite, you will go onto the reference channel (see table 1 page 9) then give a number to this satellite. For that: · Go into MENU / Installation / Channel Setup · On the line Satellite Number, choose the number with the arrows 34. If the number that you are giving is already taken, an alert message is appearing 3 seconds at the bottom of the screen. · Press on OK to give a number to a satellite and then wait until the motor stops moving. · If your motor was correctly aligned, and that you have entered the right number for HotBird, the signal indicator must be green. If it is not the case, check the alignment and your satellite numeration with your analogue receiver, if you have one. · Press on EXIT to leave all the menus and check that you effectively receive the channel from the satellite in question. · Do the same thing for the other satellites. www. metronic. com 27 8 - Remote control description 1 Digital keys. [. . . ] 1 Assembly of the plug on the cable 2 Satellite dish assembly 3 Heads (LNBs) assembly 4 Motor assembly (in the event of motorized kit) Easy Easy Easy Easy Easy Difficult Difficult Difficult Difficult Difficult 41 6 Alignment www. metronic. com · Did you isolate the LNBs (heads) ? yes no METRONIC isolated paste Other products METRONIC Silicone adhesive tape Ruban adhésif Other. . . . . . . . . . . . . · Do you think the user manual is user friendly when you have to install, without an installer, a satellite kit?yes no Which modifications would you wish to see? · Where did you install your satellite kit ?On a balcony On the roof (chimney. . . ) On the wall On the ground Other. . . . . . . . . . . . . [. . . ]