User manual METRONIC ENCEINTES MULTIMEDIA 2.1 QUICK GUIDE

[. . . ] AC Mains cable. B A TV V C R/ 110-240V~ 50/60Hz 8W ANT TV/VCR RS232 TV V C R/ 110-240V~ 50/60Hz 8W ANT TV/VCR RS232 C D E F G HI J K 8 04 - Your remote control 1 2 3 4 5 6 7 8 9 10 11 Digit pad : enter values and select the channel directly by entering its number. : power on / Standby MENU : allows you to open the menu so that you can change the settings of your Eco zapbox. Volume up / down Channel up / down OK : confirm selection in menu / on screen displays. Press twice to display technical informations about the current programme and signal. [. . . ] A - Using the EPG The Electronic Programme Guide, or EPG, is an on-screen TV guide. It shows all scheduled programmes seven days in advance for every channel. Press OK to watch the selected channel, the EPG window will close automatically. Press the green button to move to the next day's schedule and the red button to move to the previous. These are usually saved to the higher numbers, starting around channel 700. 10 B - Changing the channel You can select the channel you want to watch by using the CH5 and CH6 buttons on the remote control. When you change the channel the Info bar will be displayed for a few seconds. This shows details of the currently showing and the next programme for the selected channel. C - Changing the volume You can change the volume of your Eco zapbox by using the VOL5 and VOL6 buttons on the remote control. D - Using subtitles To use subtitles, press the button on the remote control. When subtitles have been turned on the screen below will be shown and the subtitle text will start to display on screen. E - Using digital text Many digital channels also provide digital text. Press OK button to delete all current channels and start a full auto scan. If you have set your parental code you will need to enter it to retune your Eco zapbox. · The tuning progress screen will be displayed, showing you how many channels have been found and saved. · · · · 09 - Troubleshooting Please note indoor aerial are not recommended for use with this product (this includes loft aerials) otherwise you may experience problems with reception or picture break ups on some channels. Problem Standby light not lit No signal found Possible cause Mains lead unplugged Mains fuse blown Aerial is disconnected Aerial is damaged / misaligned What to do Check mains lead Check fuse Check aerial lead Check aerial Ensure that you are capable of receiving Digital TV. 15 No picture or sound Scrambled channel message No response to remote control Forgotten PIN code You have moved your TV and you find you are no longer able to receive digital channels Tuned to digital teletext channel Channel is scrambled New batteries required Switch to another channel This Eco zapbox is not able to decode scrambled channels Plug in and turn on switch at mains Contact the helpline Try a signal booster or a direct feed from the aerial. The aerial feed maybe sent through a distributoin system which can / may reduce the digital signal now received by the Eco zapbox. 10 - Specifications Tuner and channel · RF input connector (IEC-TYPE, IEC169-2, female) · RF output connector (IEC-TYPE, IEC169-2, male) · Frequency range: 470MHz ~862MHz (UHF) MPEG-2 ISO/IEC 13818 MAX. 15Mbit/s MPEG-2 Main profile@Main level 4:3/16:9 Switchable MPEG Layer I & II, 32 / 44. 1 / 48KHz RGB, CVBS Fixed type Antenna input Composite video output, twin scart Stereo audio output, digital coaxial audio output RS-232 (for service use only) AC 230V ~50Hz MAX. 8W/standby <2W Decoder · Transport stream · Profile level · Input rate · Video format · Audio format · Video output Connection · Main power cable · Tuner · Video · Audio · Data port Power supply · Input voltage · Power consumption IMPORTANT: Due to continual revision and improvements to our products design, specifications are subject to change without notice. 16 11 - Electrical Information This Eco zapbox is fitted with a BS1363/A 13 amp plug. If it is not suitable for your supply sockets it must be removed and replaced with an appropriate plug. If the plug becomes damaged and/or needs to be replaced please follow the wiring instructions below. It must not be plugged into a supply socket as this will be an electrical hazard. If the fuse needs to be replaced it must be of the same rating and ASTA approved to BS1362. [. . . ] This symbol indicates that this 2-core appliance is Class II and does not require an earth connection. The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. 3 - Core plug WARNING : This appliance must be earthed. The wire coloured green and yellow must be connected to the terminal marked with the letter E, or by the earth symbol , or coloured green or green and yellow. [. . . ]