User manual METRONIC DINTERIEUR SLIMTECH DESIGN
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual METRONIC DINTERIEUR SLIMTECH DESIGN. We hope that this METRONIC DINTERIEUR SLIMTECH DESIGN user guide will be useful to you.
Manual abstract: user guide METRONIC DINTERIEUR SLIMTECH DESIGN
Detailed instructions for use are in the User's Guide.
[. . . ] Never open the receiver even when it is not connected, because it contains electrical components, which can be dangerous for you. In general, electrical appliances are not earthed, so you can get electrical discharges (which are not risky), while implementing the connections. Our advice is to connect the equipment after all the sockets connections have been made. To clean the receiver or its remote control, do not use any solvent or detergent. [. . . ] · Give (6) a satellite number to Atlantic Bird 3 (put 01 in case of hesitation). · If the motor does not stop at the right value, bring it with a continuous research (4) step by step (5). Exemple : Edingburg = 2°W Leave all the menus and check that you correctly receive the Atlantic Bird 3 reference channel (3). If it is not the case, you have 2 cases: First case: You do not receive anything at all, even when you slightly move the satellite dish alignment. In that case, it means that a big error has been made during the installation (mast not vertical, error between east and West, bad reading of the angle. . . ). Restart the installation from scratch while checking each detail very carefully. Second case: You have a bad reception and you have to adjust slightly the satellite dish position angle (1 or 2 degrees) to receive correctly Atlantic Bird 3. In that case, the design curve of the motor is out of line with the real curve. We then advise you to go back to the step K while putting 2° more for the Hotbird position in your area. If the result is worse, try 2° less.
(1)(3)(4)(5)(6)(7)(8)
see related paragraph page 13
20
-6 -4 -2 0 2 4
Gl
Belfast Newcastle Dublin Cork Liverpool Leeds
east / west
as
go
w
Ed ing
bu
rg
6 8 10 12
14
16 18
20
22
24 26 28 30
Gdansk
Cardiff
London Plymouth
Ham Ams Hano Lille
Brux
burg Berlin
Poznan Todz Wroclaw Warszawa
ver
Duss
Brest
Le H
eldorf Frank furt
avre
Paris
Lux
Stras
Nante
Stuttg
Tours
art Nuremb Munic h
Krakow
s
erg
Bordeau
Limog
es
Vig o
Torino
Milano
Lyon
Dijon
x
Lisboa
drid
Zara
Ma
goza
Barcelon
a
Marseill
Bilba
o
Toulouse
Trieste
e
Roma
Sevilia
Vale n
cia
Malaga
Napoli
na
Car
tage
Bari
Alger
Rab
at
Palermo
Tunis
Catan
ia
Diagram 2 : Angular reading for Atlantic Bird 3
21
M - Validation of the satellites
For each satellite, you have now to store the right position in the motor. The operation is done for Hotbird and Atlantic Bird 3, you have to do it for Astra, etc. · With 34 arrow keys, select the number of the satellite that you want to allocate to the current satellite. (Ignore the warning message) · Press OK to confirm, the motor will move to the position #1 stored in its memory. Once the motor has stopped, check that the Quality is higher than 40%. If not, it means that the motor is not correctly aligned, or that you input a wrong number. · Press EXIT until you exit all menus and check that you duly receive the channels from HotBird (or other satellites, after) Do the same procedure for the other satellites.
26
8 - Remote control description
1 Digital keys. In viewing mode, press these keys to change channel by pressing the number of the channel you want to watch. In the programming mode, these keys are used to enter the digital 2 values. Allows switching on or switching off and putting the terminal in standby. Press this key to enter in the main menu or to leave 12 the main menu. Pressing MENU in a submenu allows to exit this submenu and come back in the previous menu. In programming mode, this key is used to alter the value of a setting. [. . . ] · On the line Timer service, select Wake Up · On the line Date, input the date of the event · On the line Wake Up Time, input the start time of the event · On the line Channel, press OK to display the channel list and select the channel. · Once your settings are complete, press the black key to save and exit To create a Standby event : Use the same procedure as above, but replace Wake Up by Sleep To delete an event : · · · · Go to MENU / Config / Timer Settings. Press on the black key to save and exit.
36
18 - Troubleshooting
· The screen displays « BAD OR NO SIGNAL». Get a specialised magazine to know if the parameters of these channels have changed or if it has disappeared. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE METRONIC DINTERIEUR SLIMTECH DESIGN
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual METRONIC DINTERIEUR SLIMTECH DESIGN will begin.