User manual METRONIC 427013 QUICK GUIDE

[. . . ] It is useful to keep the degree order precision. 0 208 994 11 81 2 6 - Give a number to a satellite Check in your receiver user manual how to associate a number to each satellite. If it is not possible, leave the existing number system. 7 - Memorise a satellite position This function is generally called memorised, store, saved. . . 8 - Display the signal indicator Generally, the signal indicator appears when pressing on the INFO key. For the alignment, you need to maximise the signal then, when it is going up, optimise the quality. If the level is high, but the quality is not going up, that means that you are on another satellite, you must continue to scan. 3 0 208 994 11 81 B Necessary elements Elements and tools necessary: 1 2 3 4 5 6 7 8 9 10 11 Satellite dish Screw and fixing Offset arm Universal LNB Mast or stand off arm Recommended diameter minimum: 40 mm (1, 6'') Satellite receiver TV set PAL for digital reception and PAL/SECAM for analogue (to be able to watch it in colour) Scart lead male/male 21 pin «F» plug Cable special for satellite, (normal TV cable won't work) Motor 450908 11 13 18 10 12 17 0 208 994 11 81 4 1 1 2 4 11 3 7 5 10 8 9 6 5 0 208 994 11 81 C Prepare the motor (see diagram 2) Assembling · Make sure the fixing (tube or stand off arm) is stabilised and strictly vertical. [. . . ] Cut out at the last page of this user manual the angle system that will allow you to read precisely the motor angle. In case you damage it, you could do it all over again after downloading the user manual on the Metronic website, www. metronic. com. Position the angle system on the west side of the motor like on the picture C2, the angle is 31, 5°. Adjust the nut from the 2c screw to display the incline of your location. When the right angle as been adjusted, tighten the screw, and the nut 2d as well. 0 208 994 11 81 8 Inclination and angular reading for Hotbird 3 9 0 208 994 11 81 D Connection For the installation you will need 2 pieces of cable. The first one, roughly 1, 5m (4, 92ft) to go from the LNB to the motor, the second one as long as it takes to go from the motor to the receiver. Prepare the cables and assemble the "F" plug at the end of the cable. Respect the dimension indicated on the diagram below; the plug must screw on the aluminium foil roll up. Make sure that none of the braid strand is in contact with the central core of the cable. Put the motor near the receiver, on a table or on the floor, and connect the receiver LNB input to the Motor DEMO output with the 1, 5m (4, 92ft) cable, then switch on the receiver. Moteur Horizon-Horizon Réf. 450908 S/N 3mm441550nnnnnn 0 208 994 11 81 10 E Reset the motor and checking of the stop The reset of the motor is to reinitialise its position, and not to put him at 0°, which means face south. Do not go to step L (adjusting the alignment) if you do not receive it. 1) Put the receiver on the Hotbird reference channel then display the signal indicator (8). 2) Launch a slow scan (for 20 seconds) a quarter of the way on the right, then a quarter of the way on the left while pivoting the whole (satellite dish + rotor) around the mast, while checking the level. If the level is not going up, increase the satellite dish incline of 2° and do the same manual scan. Carry on as above by step of 2° followed by a scan until the level increase. When you are on the right satellite, the image will appear in the background. Adjust it to obtain the maximum in level and quality (bar the longest as possible). In some area, it is normal that you will turn up to 20 scanning, be patient. Block the elevation by tightening the lock nut 12a. WARNING: a too important tightening of the U-bolt 2e (diagram 2 page 7), may break one of the fixing clamp. (8) Go to corresponding paragraph page 2 and 3 17 0 208 994 11 81 L Orientation adjustment · Put the receiver on the Atlantic Bird 3 reference channel. (1) · Check in diagram the Atlantic Bird 3 angular reading of your geographical area. · Give (6) a satellite number to Atlantic Bird 3 (put 01 in case you hesitate). · If the motor does not stop at the right value, bring it with a continuing research (4) or step by step (5). [. . . ] In that case, the design curve of the motor is out of line with the real curve. We then advise you to go back to the step K while putting 2° more for the Hotbird position in your area. 18 (2)(3)(4)(5)(6)(7) 0 208 994 11 81 Go to corresponding paragraph page 2 and 3 Angular reading for Atlantic Bird 3 19 0 208 994 11 81 M Satellite validation For each satellite, you have now to memorise the right position in the motor. The operation is done for Hotbird and Atlantic Bird 3, you have to do it for Astra, etc. [. . . ]