User manual METO-FER SPRING FEEDER FG

[. . . ] 355 Wyoming Street Pittsburgh, PA 15211 Phone: 412-488-3488 Fax: 412-488-3498 www. meto-fer. com PLEASE, SAVE THIS MANUAL FOR FUTURE REFERENCE 04/06/02 Page 1 Function The spring feeder facilitates the disentangling and feeding of springs. [. . . ] The tappet of the hopper conveys the springs on the chute by means of a lifting movement in front of the slide. If the drum is empty (is controlled by a light barrier), the slide is opening automatically; the springs slide into the unit. Simultaneously and without loss of time, the chute is filled up again with springs by an exactly defined quantity of lifting s. Remarks: The unit is factory set from Meto-Fer for the corresponding springs. The unit is supplied with a matching nuzzle, tube mount and 2 meter tube. Operation Instruction Switch off the unit=> push up the toggle switch Fill up the drum with springs; ca. 0. 3- 0. 5 Liter Connect current supply=> 24V DC Check slide to make sure it is properly closed Connect compressed air, set approximately 6 bar Switch on the unit=> push down the toggle switch (green light on) If all is switched on correctly and the ring initiator is not initialized, the unit will automatically start functioning Page 2 Maintenance The spring feeder does not need maintenance. It is recommendable to clean the housing in scheduled time periods. ] Input/ output points Input 12 13 14 17 From light barrier Slider closed (Q0) Slider open (QL) Ring initiator Output Q1 Q2 Q3 Q4 Q5 To Agitating-ON Blow out-ON Slider-ON Hopper-ON Warning light Who controls what Factory Settings 0. 17 Sec. Cycle 5 Liftings 7/10 Cycles Name T1 T2 T3 T4 T5 T6 T7 T8 C1 C2 C3 Function Agitating time (spinning and dispersion) Blowing time (blow the spring into the tube) Pause agitating again (Pause 1) Opening time when slider is open Hopper slider Warning light Short pause (setting of springs; Pause 2) Conveyor control Periodical control of the light barrier Filling up of the hopper: § qty. [. . . ] For leaving the menu, press ESC. Step 1 2 Action Press key OK Go down with cursor twice Press key OK Cursor up or down Effect Menu choice Indicator PARAMETER is flashing Picture timer Choose timer or counter Choose the wished placed (is flashing) Change numerical value to the wished size New value is stored Standard view 3 4 5 Cursor to left or right 6 Cursor up or down 7 8 Press key OK Press key ESC twice Page 4 Control box wiring diagram Terminal connections: Connection right Ls send+ 2k7_ Ring initiator Slider close Easy supply Above Above Above Below Below Slider open Easy supply Receiver Input 24VDC+ Easy minus Above Output 24VDC- Above Connection Connection Easy Control + + Left below below below -- -- -- below I10 I11 I12 I1 I2 I3 I4 I5 I6 I7 I8 I9 + - - -- RIGHT above above above Above Below Below Warning light Easy supply Easy supply Easy supply Easy supply LED LED Blow out Spinning PG Input/ output wiring Input signals (Sensors) Terminal 1 ¥ Ring ¥ initiator Hopper Supply Supply Slider Output 24VDC Output signals (Valves) Terminal 4 Terminal 5 Terminal 6 Terminal 7 Terminal 2 ¥Lightbarrier receiver Terminal 3 ¥ Lightbarrier transmitter ¥ Slide close ¥ Slide open ¥ ¥ ¥ ¥ Slide Hopper Warning Light ¥ ¥ ¥ ¥ Supply Corner Spinning blow out Page 5 Below + - 01 02 03 04 05 06 07 08 [. . . ]