User manual MERCEDES E 300 4MATIC MANUAL 2009

[. . . ] E-Class Operator's Manual Symbols Trademarks®: RBluetooth® is a registered trademark of Bluetooth SIG Inc. RESP® YY and PRE-SAFE® are registered trademarks of Daimler. is a registered trademark of Prince, a Johnson Controls Company. This continuation symbol marks a warning or procedure which is continued on the next page. Display Text in displays, such as the control system, are printed in the type shown here. RHomeLink® The following symbols are found in this Operator's Manual: G Warning! Warning notices draw your attention to hazards that may endanger your health or life, or the health or life of others. !Highlights hazards that may result in damage to your vehicle. i Helpful hints or further information you may find useful. [. . . ] X Turn mounting element 2 in the cargo rail to N. Installing: Fold seat backrests 3 forward (Y page 207). X Insert storage box 1 from within the cargo compartment with the opening pointing in direction of travel. X Press locking hooks 4 of storage box 1 into the space between seat backrests 3 and cargo compartment floor 2. X Fold seat backrests 3 to the original position (Y page 208). 212 Controls in detail Loading and storing Storage box 1 is additionally held in place from above by the twin roller blind. X Fill storage box 1 with cargo through the opening on the front side. X Fold seat backrests 3 to the original position (Y page 208). X X Twin roller blind (wagon) The twin roller blind contains a cargo net and a cargo compartment cover. Pull cargo net 1 up and hook it onto mounting 2. Cargo net 1 should then be hooked onto the front mountings. i You can use cargo net 1 even when the Cargo net G Warning! The cargo net cannot hold back heavy loads. Objects which are insufficiently secured could otherwise injure you if they are thrown around in the event of an accident, during hard braking or steering maneuvers. Cargo compartment cover To assist loading the cargo area when the cargo compartment cover is closed, the cover will be released and automatically raised/ lowered when opening/closing the tailgate. Removing: Fold seat backrests 3 forward (Y page 207). X Slide locking hooks 4 of storage box 1 forward out of the retainers. X Pull storage box 1 to the rear and remove it from cargo compartment. When loading the vehicle, make sure not to load the cargo compartment over the lower edge of the side windows. The twin roller blind could otherwise be damaged when the tailgate is being closed. 1 Cargo net 2 Mounting for cargo net Z 213 Controls in detail Loading and storing Removing the twin roller blind X Roll up cargo net and cargo compartment cover 2. X Fold the driver's side rear seat backrest forward (Y page 207). X Push twin roller blind to the driver's side out of its anchorage on the seat backrest and remove it. Opening the cargo compartment floor 1 Handle 2 Cargo compartment cover Rolling up the cargo compartment cover X Use handle 1 to pull cargo compartment cover 2 down into the horizontal position. X Unhook cargo compartment cover 2 from its anchorages on the left and right sides. To do so, pull cargo compartment cover 2 slightly towards the rear and lower it. Pulling out the cargo compartment cover X Pull out cargo compartment cover 2 towards the rear until it engages. 1 Front cargo compartment floor 2 Rear cargo compartment floor 3 Handle X Storage space under the cargo compartment floor (wagon, E 63 AMG only) The vehicle tool kit and jack are stored under the rear cargo compartment floor. A loading tray and a folding box are located under the front cargo compartment floor. Use handle 3 to open cargo compartment floor 1 or 2. 214 Controls in detail Loading and storing Closing the front cargo compartment floor X Closing the rear cargo compartment floor Swing front cargo compartment floor 1 downward. X Push front cargo compartment floor 1 downward on handle 3 until it locks into place. 2 Rear cargo compartment floor 4 Locking in place 5 Hooks 6 Pneumatic spring X 6 Pneumatic spring 7 Release button X Press rear cargo compartment floor 2 slightly forward 4. Pneumatic spring 6 engages, locking rear cargo compartment floor 2 in place. compartment floor is open and hang light luggage items from hooks 5. i You can transport objects when the cargo Press release button 7 and swing rear cargo compartment floor 2 downward. X Push front cargo compartment floor 1 downward on handle 3 until it locks into place. Z 215 Controls in detail Loading and storing Removing the rear cargo compartment floor X Move rear cargo compartment floor 2 into an almost vertical position (to an angle of 85°). [. . . ] If you use a solution that is more than 55% anticorrosion/antifreeze (freeze protection to approximately -49 [-45]), the engine temperature will increase due to the lower heat transfer capability of the solution. Therefore, do not use more than this amount of anticorrosion/antifreeze. If the coolant level is low, water and MB 325. 0 Anticorrosion/Antifreeze should be used to bring it up to the proper level (have cooling system checked for signs of leakage). Please make sure the mixture is in accordance with label instructions. [. . . ]