User manual MEMOREX MVDR2102AOM

[. . . ] LOCATION OF CONTROLS QUICK SET UP GUIDE ON/STANDBY Button DV IN Jack, S-Video IN Jack and A/V IN Jacks (under door) 3. RF IN Jack Rear Video IN Right Audio IN (Rear Video/S-Video) Component Y Output Component Cb/Pb Output Video OUT Right Audio OUT AC Power Cord Optical Digital Audio Output Coaxial Digital Audio OUT Left Audio OUT S-Video OUT Component Cr/Pr Output Left Audio IN (Rear Video & S-Video) S-Video IN RF OUT Jack 1. 2. How do I stop the picture from rolling/flickering: This could be caused by the accidental pressing of the I/P (Interlace/ Progressive) button. If using a TV that is not compatible with progressive scan, press this button to select Interlace. [. . . ] To do this, select MANUAL SCAN using the Navigation (, ) buttons 1 followed by the ENTER button 2. Select the channel memory using the Channel Up or Down buttons 3, then press the Navigation (®) button 1 and the unit will cycle through and stop at the first available station. If you want to keep the station, select OK using the Navigation (, ®) buttons 1 then press the ENTER button 2; the station will be saved on the channel. OR select CANCEL using the Navigation (, ®) buttons 1 then press the ENTER button 2. Press the Navigation (®) button 1 to scan for the next available station. (Please see additional information in NOTES below. ) NOTES: · It is highly recommended to perform the AUTOMATIC SEARCH to scan all channels and store the active channels into memory when first using the set. If you have not scanned for the available channels or stations, then you may not be able to record the TV channel. · During Manual Scan, press the STOP (X) button to cancel searching. · When all the available stations are searched, then "Scan is Over" will appear on the screen, press the ENTER button followed by the Navigation (®) button to search for the desired station again. · To return to the previous row of options, press the Navigation () button. · To exit setup, press the SETUP button. 30 EDITING TV CHANNELS INITIAL SETUP MENU (CONTINUED) 1 2 1 2 1 2 While in the TV Tuner mode, enter the TV Setup page as described on the previous page. Then, select CH Edit using the Navigation (, ) buttons 1, then press the ENTER button 2. To Skip the currently viewed channel select SKIP using the Navigation (, ) buttons 1, then press the Navigation (®) button 1 to select ON to skip the channel when using the Channel Up or Down buttons 2. To Add the currently viewed channel select SKIP using the Navigation (, ) buttons 1, then press the Navigation (®) button 1 to select OFF to not skip the channel when using the Channel Up or Down buttons 2. 3 4 1 2 Follow procedure in step 1. To Fine Tune the currently viewed channel select CH FINE TUNE using the Navigation (, ) buttons, then press the Navigation (, ®) buttons repeatedly to fine tune the selected station as desired. Follow procedure in step 1. To Copy the currently viewed channel into another channel number, select COPY TO using the Navigation (, ) buttons 1 then select the desired channel number using the Navigation (, ®) buttons 1. To Exchange the currently viewed channel with another channel number, select EXCHANGE FROM using the Navigation (, ) buttons 1 then select the desired channel number using the Navigation (, ®) buttons 1. When done, press the ENTER button 2 to make the change. NOTES: · To Edit another TV channel, use the Channel Up or Down buttons or the Number buttons to enter the desired channel to view and edit. 31 MTS SETTING INITIAL SETUP MENU (CONTINUED) Some TV programs broadcast additional audio. For example, if a program is available in English and Spanish, Spanish can be broadcast as the additional audio program. To record TV programs in stereo, SAP or Dual, you can select Stereo, SAP or Dual as the default setting. 1 1 2 NOTES: · The MTS setting does not become active until the sound of a TV program is transmitted in Stereo or SAP. · When you playback the recording, you can playback the sound only in the setting you selected for recording (i. e. , a recording in SAP can be played back only in SAP). · To return to the previous row of options, press the Navigation () button. [. . . ] Move obstacle. No picture. The disc is dirty or inserted incorrectly. The equipment connected with the audio cable is not set to receive the DVD signal input. There is an obstacle in the path of the beam. No sound. The playback picture is poor. The remote control is not working. 66 DVD The unit does not start playback. SYMPTOM TROUBLESHOOTING GUIDE (CONTINUED) DVD not inserted, or inserted upside-down. [. . . ]