User manual MEMOREX MVD-2256

[. . . ] If using a compatible TV, select Progressive and connect this unit using the Component jacks on the rear of this unit. COMMON QUESTIONS How do I select a different channel?For ANTENNA, enter a two digit channel number; i. e. , enter "02" for Channel 2, enter "69" for Channel 69. For CATV, enter a three digit channel number; i. e. , enter "002" for Channel 2, enter "125" for Channel 125. 1 23 4 5 6 7 8 9 10 11 12 6. 16. CONNECTING THE DVD TO A TV AND CATV USING THE RF INPUT/OUTPUT JACKS BASIC CONNECTIONS TV SETUP PAGE: When the recorder is turned on for the first time, there will be several wizard pages displayed one by one which will allow you to set the basic options as follows: 1. [. . . ] (Please see additional information in NOTES right. ) 29 While in the TV Tuner mode, enter the Setup menu as described on page 20, then select the TV Setup page using the Navigation (, ) buttons followed by the Navigation (®) button, then select/change the setup option. This unit is equipped with a channel memory feature which allows channels to skip up or down to the next channels set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the unit's memory. In addition to normal VHF/UHF channels, this unit can receive up to 125 Cable TV channels. First set the TV SIGNAL option, then follow the steps in AUTO CHANNEL SCAN below. TV SETUP PAGE: INITIAL SETUP MENU (CONTINUED) TV SIGNAL 1 AUTO CHANNEL SCAN 1 1 2 1 2 While in the TV Tuner mode, enter the TV Setup page as described above. Then, select TV SIGNAL using the Navigation (, ) buttons 1, then the Navigation (®) button 1 to select it. Select ANTENNA or CATV using the Navigation (, ) buttons 1, then press the ENTER button 2. Select CATV if using cable television or ANTENNA if using an outdoor antenna. Follow the steps in the TV SIGNAL section (left), then select AUTOMATIC SEARCH using the Navigation (, ) buttons 1 followed by the ENTER button 2. Select OK using the Navigation (, ®) buttons 1 followed by the ENTER button 2; the unit will then automatically cycle through all the channels and store active channels into memory. During AUTOMATIC SEARCH, press the ENTER button 2 to cancel searching. (Please see additional information in NOTES below. ) MANUAL SCAN 1 1 2 3 It is recommended to perform AUTO SCAN instead of MANUAL SCAN. · To return to the previous row of options, press the Navigation () button. · To exit setup, press the SETUP button. Enter the TV Setup page as described on the previous page. Then, select MTS SETTING using the Navigation (, ) buttons 1, then the Navigation (®) button 1 to select it. Select the desired setting using the Navigation (, ) buttons 1, then press the ENTER button 2. (Please see additional information in NOTES at the right. ) 32 1 TUNER OPERATION 2 Press the STANDBY ON/OFF button to turn on the unit. After a few seconds, the Source mode (TV Tuner, Front AV, Front SV, etc. ) screen will appear. Press the SOURCE button to select TV, "Input Tuner" and a channel number will appear on the TV. If there is no signal for the channel, "No signal" will appear on the screen. 3 4 1 2 1 2 For proper operation, before selecting channels, they must be set into the TV's program memory, see page 30. The TV automatically stops at the next channel set into memory. Direct Program Selection buttons (0- 9) Use these buttons to select a channel. The channel number will appear at the top right corner of the screen. For ANTENNA, enter a two digit channel number; i. e. , enter "02" for Channel 2, enter "69" for Channel 69, etc. For CATV, enter a three digit channel number; i. e. , enter "002" for Channel 2, enter "125" for Channel 125, etc. NOTE: · When ANTENNA/CATV option is set to ANTENNA, only channels from 02 to 69 can be selected. When set to CATV, channels up to 125 can be selected. FAQs: Why do I only receive up to channel 69, when my cable goes much higher? [. . . ] However, the only difference is the unit will resume to the normal Stop mode after recovering successfully from the power failure. 65 Check the following before requesting service: SYMPTOM GENERAL No power. Power on, but unit not functioning properly. TROUBLESHOOTING GUIDE POSSIBLE CAUSE POSSIBLE SOLUTION AC cord unplugged. Unplug the unit and wait about one to two hours to allow the player to dry. Select the correct TV type (16:9, Panscan or Letterbox) which matches the TV. [. . . ]