User manual MELICONI PRATICO 2

[. . . ] IMPORTANT: The remote control must not be exposed to excessive heat sources. USE OF THE BUTTONS AND FUNCTIONS The functions of the buttons described below are available only if they exist on your device. Try pressing a number button and check that the red light remains lit continuously until you release the button. If the light flashes, the batteries inserted are not charged and are about to go flat, therefore you must substitute them. [. . . ] If they don’t, you are probably using an incorrect code destined for a very similar device; at this point ignore the SMS list and consult the SETTING CODES USING A MANUAL CODE section to find a more suitable code. NOTE: If you don’t receive an SMS on your cell phone or if the message says ERROR / NO CODE, it means the system has not been able to process the data you have sent. Do not try sending another SMS use the SETTING CODES USING A MANUAL SEARCH procedure instead. SETTING CODES USING A MANUAL SEARCH (only to be performed if the specific code could not be found) 1. Press and hold down for 6 seconds the device selection button corresponding to the device you wish to enter the code for. If the device does NOT switch off, press the same button again slowly (it may be necessary to press the button several times). Three long flashes indicate that the operation has been carried out correctly. CHECK Check that the other buttons correspond to the functions of the original remote control; if not, it is likely that the code found is incorrect, but is used for a very similar device. If the manual search for the code is successful, obtain the code in use by following the DISPLAY CODE IN USE procedure and make a note of it inside the battery cover. NOTE: During the search the indicator stops flashing and the remote control exits the programming mode in the following cases: • if for 12 seconds the button indicated is not pressed or if another button is pressed • if the list of codes to find is terminated. Com website 8 ENTERING THE CODE DIRECTLY (only to be performed if you know the specific code to be set) 1. Press and hold down for 6 seconds the device selection button corresponding to the device you wish to enter the code for. If the result is still negative, it means the code indicated is not included in the remote control. (see following section) INTERNET UPDATE Today you can download from the internet directly to your remote control the codes of the latest devices or those which will be brought out in future, codes which would not otherwise be available using traditional programming methods. To do this you need to purchase the special MELICONI Audiocable, which allows you to download the information you need onto any PC using an internet connection. DISPLAY CODE IN USE If you set up the remote control using the MANUAL SEARCH procedure, obtain and make a note of the code in use as follows: 1. Press and hold down for 6 seconds the device selection button corresponding to the device you wish to enter the code for. After a pause of several seconds, the indicator light produces four sets of flashes, spaced out, corresponding to the code to be obtained. Make a note of the code obtained on the label on the inside of the battery cover. 9 TROUBLESHOOTING PROBLEM The device does not respond and the indicator light does not come on when a button is pressed. [. . . ] Improper disposal of the product by the user will be subject to the sanctions in Legislative Decree No. U hoeft alleen een SMS te sturen naar het nummer 0039 345 7518893, waarin u de volgende gegevens vermeldt: 2B, type, merk, model - Type = het te bedienen toestel aangeven met behulp van een van de volgende afkortingen: TV - SAT - TER (terrestrische decoder) - Merk, model = het merk en model van het te bedienen toestel aangeven. Model afstandsbediening Pratico 2 Aankoopdatum Stempel verkoper Het symbool op het apparaat van de container met het kruis erdoor betekent dat het product aan het eind van zijn levensduur apart van ander afval verwerkt moet worden. NOTA: Durante a operação de busca o indicador pára de laqmpejar e o controlo remoto sai do modo programação nos seguintes casos: • se por 12 segundos não for pressionada a tecla indicada ou se for pressionada uma outra tecla • se a lista dos códigos a buscar tiver acabado. [. . . ]