User manual MCINTOSH C1000 CONFIGURABLE TUBE/SOLID STATE CONTROLLER AND PREAMPLIFIER

[. . . ] 2A CDR (5) RIGHT Channel OUPTUTS (Balanced) contain the selected Record Source Signal for recorders MAIN RIGHT Channel OUTPUTS (Balanced) contain Listen program signals at all times MAIN/SPKR 1 and 2 RIGHT Channel OUTPUTS (Balanced) contain Listen signals and may be assigned either as two additional Main Outputs (active all the time) or switched On/Off with the Remote Control SPKR 1 and 2 Push-buttons SPKR 1 and 2 RIGHT Channel OUTPUTS (unbalanced) contain Listen signals and are switched On/Off with the Remote Control SPKR 1 and 2 Push-buttons SRVR (4) and CDR (5) RIGHT Channel OUPTUTS (Unbalanced) contain the selected Record Source Signal for recorders PROCESSOR RIGHT Channel LISTEN TO and FROM allow an external signal processor to be connected for use in the Listen mode CD (6), CDR (5) and D/A (7) RIGHT Channel INPUTS (Balanced) accept high level program source signals C1000 Preamplifier Rear Panel Connections RIGHT PREAMPLIFIER INPUT A Connector accepts the custom McIntosh 21 Conductor Cable. [. . . ] MC (9) Input accepts the low level signals from a Moving Coil Phono Cartridge McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 Part No. 04100200 2B CDR (5) RIGHT Channel OUPTUTS (Balanced) contain the selected Record Source Signal for recorders MAIN RIGHT Channel OUTPUTS (Balanced) contain Listen program signals at all times MAIN/SPKR 1 and 2 RIGHT Channel OUTPUTS (Balanced) contain Listen signals and may be assigned either as two additional Main Outputs (active all the time) or switched On/Off with the Remote Control SPKR 1 and 2 Push-buttons SPKR 1 and 2 RIGHT Channel OUTPUTS (unbalanced) contain Listen signals and are switched On/Off with the Remote Control SPKR 1 and 2 Push-buttons SRVR (4) and CDR (5) RIGHT Channel OUPTUTS (Unbalanced) contain the selected Record Source Signal for recorders PROCESSOR RIGHT Channel LISTEN TO and FROM allow an external signal processor to be connected for use in the Listen mode C1000 Tube Preamplifier Rear Panel Connections CD (6), CDR (5) and D/A (7) RIGHT Channel INPUTS (Balanced) accept high level program source signals RIGHT PREAMPLIFIER INPUT C INPUT RECORD LINK INPUTS (BalConnector accepts the cusanced) connect to the Record tom McIntosh 21 Conductor Link RIGHT Channel Input on Cable. This cable connects the C1000P Preamplifier when the to the C1000C RIGHT C1000T and a C1000P PreampliCONTROLLER OUTPUT fiers are both connected to the C. It supplies the control same C1000C Controller, allowing signals and power supply for the sharing of their inputs for voltages for the Right Chanrecording purposes nel Circuitry in the Tube Preamplifier LEFT PREAMPLIFIER INPUT D Connector accepts the custom McIntosh 21 Conductor Cable. It supplies the control signals and power supply voltages for the Left Channel Circuitry in the Tube Preamplifier RECORD LINK INPUTS (Balanced) connects to the Record Link LEFT Channel Input on the C1000P Preamplifier when the C1000T and a C1000P Preamplifiers are both connected to the same C1000C Controller, allowing for the sharing of their inputs for recording purposes CD (6), CDR (5) and D/A (7) LEFT Channel INPUTS (Balanced) accept high level program source signals CDR (5) LEFT Channel OUPTUTS (Balanced) contain the selected Record Source Signal for recorders MAIN LEFT Channel OUTPUTS (Balanced) contain Listen program signals at all times MAIN/SPKR 1 and 2 LEFT Channel OUTPUTS (Balanced) contain Listen signals and may be assigned either as two additional Main Outputs (active all the time) or switched On/Off with the Remote Control SPKR 1 and 2 Push-buttons SPKR 1 and 2 LEFT Channel OUTPUTS (unbalanced) contain Listen signals and are switched On/Off with the Remote Control SPKR 1 and 2 Push-buttons SRVR (4) and CDR (5) LEFT Channel OUPTUTS (Unbalanced) contains the selected Record Source Signal for recorders PROCESSOR LEFT Channel LISTEN TO and FROM allow an external signal processor to be connected for use in the Listen mode PROCESSOR LEFT Channel RECORD TO and FROM allow an external signal processor to be connected for use in the Record mode GND (Ground) connectors for connecting the Turntable Ground Wire to the C1000T Chassis TUNER (3), DVD (1), SRVR (4) and AUX (2), LEFT Channel INPUTS (un-balanced) accept high level program source signals PROCESSOR RIGHT Channel RECORD TO and FROM allow an external signal processor to be connected for use in the Record mode TUNER (3), DVD (1), SRVR (4) and AUX (2), RIGHT Channel INPUTS (un-balanced) accept high level program source signals PHONO INPUTS RIGHT MM (8) accepts signals from a Moving Magnet Phono Cartridge. [. . . ] MC (9) Input accepts the low level signals from a Moving Coil Phono Cartridge [. . . ]