User manual MCCULLOCH TRIMMAC 280, 28CC

[. . . ] TrimMac 280 GB INSTRUCTION MANUAL IMPORTANT INFORMATION: Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference. FR MANUEL D'INSTRUCTIONS RENSEIGNEMENTS IMPORTANTS: Avant d'utiliser cet appareil, veuillez lire atentivement les instructions et assurez-vous de les avoir comprises. Conservez les instructions pour référence ultérieure. DE BETRIEBSANWEISUNG WICHTIGE INFORMATION: Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen verstanden haben und gut aufbewahren. ES MANUAL DE INSTRUCCIONES INFORMACIÓN IMPORTANTE: Lea atentamente las instrucciones y asegúrese de entenderlas antes de utilizar esta aparato. [. . . ] S If the rotor will not rotate freely due to frozen ice, thaw the unit before thoroughly before attempting to operate under power. The snow thrower could propel small objects at high speed causing injury. S After striking a foreign object, stop the engine, disconnect spark plug and inspect the snowthrower for damage and repair if necessary before restarting unit. S Never operate the snowthrower near glass enclosures, automobiles and trucks. Never attempt to use the snowthrower on a roof. S Let snowthrower run for a few minutes after clearing snow so moving parts do not freeze. Exercise caution to avoid slipping or falling, especially when operating in reverse. S Know how to stop quickly. ASSEMBLY If received assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure. Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer. WARNING: 2. Position locking/release button of attachment into guide recess of coupler. Push the attachment into the coupler until the locking/release button snaps into the primary hole. Before using the unit, tighten the knob securely by turning clockwise. Coupler Primary Hole Guide Recess INSTALLING TRIMMER ATTACHMENT CAUTION: When installing trimmer attachment, place the unit on a flat surface for stability. Coupler LOOSEN Shipping protector Upper Shaft Locking/ Lower Release Button Attachment TIGHTEN Knob WARNING: Make sure the locking/ release button is locked in the primary hole and the knob is securely tightened before operating the unit. All attachments are designed to be used in the primary hole. 7 For optional attachments, see the ASSEMBLY section of the applicable attachment instruction manual. Slot Shield Bracket ATTACHING THE SHIELD WARNING: The shield must be properly installed. The shield provides partial protection from the risk of thrown objects to the operator and others and is equipped with a line limiter which cuts excess line. Nut Line Limiter Blade ADJUSTING THE HANDLE WARNING: When adjusting the handle, be sure it remains between the trigger and the safety label. Rotate the handle on the shaft to an upright position; retighten wing nut. OPERATION Be sure to read the fuel information in the safety rules before you begin. If you do not understand the safety rules, do not attempt to fuel your unit. Contact an authorized service dealer. WARNING: HOW TO STOP YOUR UNIT S To stop the engine, move the ON/OFF switch to the OFF position. FUELING ENGINE ON/OFF Switch WARNING: Remove fuel cap slowly when refueling. Before operation, gasoline must be mixed with a good quality 2-cycle air-cooled engine oil. A 40:1 ratio is obtained by mixing 5 liters of unleaded gasoline with 0, 125 liter of oil. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. [. . . ] Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Keep all parts of your body away from the cutting attachment and muffler. Idle Speed Adjustment Allow engine to idle. Adjust speed until engine runs without trimmer head moving or spinning (idle speed too fast) or engine stalling (idle speed too slow). S Turn idle speed screw clockwise to increase engine speed if engine stalls or dies. [. . . ]