User manual MCCULLOCH BRICOMARCHEBMD3800

[. . . ] A. D. Partner McCulloch oil oil 40:1 50:1 2T oil 25:1 2% 1 ltr 4 5 10 20 80 100 200 400 2, 5% 100 125 250 500 4% 160 200 400 800 20 cm3 25 cm3 40 cm3 B. 1 2 3 E. 1 2 4 INSTRUCTION MANUAL BRUGERHNDBOG 5 6 GB I IMPORTANT INFORMATION: Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference. DK VIGTIGE OPLYSNINGER: Ls instruktionerne omhyggeligt, fr du bruger enheden og gemme til senere henvisning. LIBRETTO D'ISTRUZIONI INFORMAZIONI IMPORTANTI: Leggere le istruzioni attentamente e capirle bene prima di usare il prodotto. Conservare per ulteriore consultazione. OHJEKIRJA FIN N TRKE TIETOA: Lue nm ohjeet huolellisesti ja varmista, ett olet ymmrtnyt ne, ennen kuin alat kytt tt laitetta ja silyt myhemp tarvetta varten. MANUEL D'INSTRUCTIONS BRUKERHNDBOK VIKTIG INFORMASJON: Les disse anvisningene nye og forsikre deg om at du forstr dem fr du bruker enheten og oppbevar dem for sen-ere bruk. F RENSEIGNEMENTS IMPORTANTS: Avant d'utiliser cet appareil, veuillez lire atentivement les instructions et assurez-vous de les avoir comprises. Conservez les instructions pour rfrence ultrieure. C. 1 2 3 F. 1 2 3 BETRIEBSANWEISUNG MANUAL DO OPERADOR D WICHTIGE INFORMATION: Lesen Sie diese Hinweise zur Handha-bung des Gerts aufmerksam durch. [. . . ] Do not attach any blade to a unit without proper installation of all required parts. Failure to use the proper parts can cause the blade to fly off and seriously injure the operator and/or bystanders. When using the unit always hold the front part of the machine (blade or nylon string head) below your waist. NYLON STRING HEAD: Always make sure it has been correctly assembled and fitted. The nylon head is suitable to cut grass and weeds wherever there might be obstacles like trees, fences or walls. The nylon string head also reduces the likelihood of damaging small plants and trees bark. Only use flexible, nonfilament nylon line in the nylon line head as specified by the manufacturer. Never use metallic line which could break off and become a dangerous projectile. When fitting or changing a cutting device, ensure you follow the instructions in the section "Blade or nylon string head assembly" with extreme precision. Fit these cutting devices using all and only the parts as described, and in the correct order. A blade with worn teeth besides providing poor performance might also generate a sudden thrust. This can result in a violent sideways kick caused when the blade touches against wood or solid bodies, such thrust might then cause the operator to loose control of the machine itself. Never attempt to work with a damaged blade but replace it with a new one. THRUST: can occur when using any type of circular blade within the risk area: therefore it is advisable to cut using the remaining area of the blade. CIRCULAR SAW BLADE: it can be used to cut sappling, small trees with a diameter up to 7 cm. , to clean shrubs. WARNING: IF A METAL 24-80 TOOTH BLADE IS USED (A TOOTH SAW BLADE) A DOUBLE SHOULDER HARNESS AND A SAFETY A 7 A GUARD (PROTECTION) MUST ALSO BE USED AS MARKED IN THE SUMMARY CHART (SEE CLOTHES SECTION IN SAFETY CHAPTER: ALWAYS WEAR A HELMET). ALWAYS USE GENUINE ACCESSORIES AND SPARE PARTS AVAILABLE FROM AUTHORISED SERVICING DEALERS. THE USE OF NON-ORIGINAL ACCESSORIES AND SPARE PARTS INCREASES THE RISK OF ACCIDENTS AND IN SUCH A CASE THE COMPANY IS NOT LIABLE FOR DAMAGE TO PEOPLE AND/OR THINGS. D. This product is fitted with a 2-stroke engine and therefore requires a 2-stroke petrol and oil mix. In order to obtain a good fuel mix, put the oil into the container before the petrol. The use of sub-standard petrol or oil may reduce performance or reduce the life of certain components. UNLEADED PETROL If using unleaded petrol, you must use a totally synthetic 2-stroke engine oil or branded 2-stroke engine oil, see table. [. . . ] To set high speed screw (H) : close screw (H) turning it clockwise without forcing . If the engine speed is too high open the screw about 1/8 turn (counterclockwise ) I: The (I IDLE) screw controls the throttle opening to govern idle speed (2, 800 min-1) adjust as necessary. CAUTION: increased idle speed may cause blade or nylon string head movement. For precise adjusting contact an authorised service station which offers the latest in toll, parts and technical assistance. M. [. . . ]