User manual MAYTAG MDE9601

[. . . ] · Damaged mains cables must only be replaced by a qualified professional. · Sufficient ventilation is required to prevent smoke from open fires or fumes from equipment burning other fuels being sucked into the room. Packing material Disposal Sort waste in accordance with local guidelines. When the machine has reached the end of its service life and is to be disposed of, it should immediately be made unusable. Contact your local authority for information about where your old machine should be disposed of and recycled in the proper way. [. . . ] You can now start the machine as usual 7 The text in the display indicates that the programme has finished. If the Anti-crease option has been selected, the drum will rotate every minute for two hours after cooling. Drying programme finished Important!If the fluff filter becomes clogged, the machine's automatic overheating cut-out may be triggered. To enable the machine to be restarted, the filter must be cleaned and the machine allowed to cool for around 30 minutes. The filter may need to be cleaned if limescale deposits occur, see "Care and cleaning" chapter. 6 Press the Start button Drying time remaining An estimate of the remaining drying time will be shown in the display within 2 minutes of the drying programme starting. For example, 1:35 means that approximately 1 hour and 35 minutes remain until the load achieves the selected level of dryness. If the Anti-crease option has been selected, the drum will rotate every minute for two hours after cooling. If you want to stop or change a programme Press and hold the Start/Stop button for three seconds. The programme is not affected if the programme selector is changed after the programme starts. To load or remove washing If you want to load or remove washing once you have started the machine, open the door and the machine will stop automatically. Load more washing, close the door and press the Start/Stop button. 2 1 10 Switch off the main power switch. Remove the clothes, and close the door to prevent small children from climbing into the machine. 8 Once drying has finished 11 Consumption values For the consumption values given below, the following prerequisites apply: Temperature of intake air: 20 °C. Before tumble-drying, cotton fabrics are spun at 800 and 1600 rpm (long spin). Before tumble-drying, other fabrics (crease-resistant and acrylic) are spun at 800 rpm (short spin). Dry Extra Dry Programme Cotton, linen Cotton, linen Cotton, linen Material Normal Normal Normal Normal Normal Normal Low Energy Programme consumption Max. min. ) Temperature (kg) 800 rpm 1600 rpm 800 rpm 1600 rpm 6. 0 6. 0 3. 0 6. 0 3. 0 3. 0 6. 0 4. 1 3. 7 1. 6 3. 5 1. 5 1. 8 2. 8 3. 2 2. 9 2. 6 1. 9 130 120 110 50 55 85 50 105 90 85 55 - Normal Dry Normal Dry Normal Dry Iron Dry Dry Crease-resistant, polyester/cotton Crease-resistant, polyester/cotton Acrylic, rayon, acetate Cotton, linen 12 Care and cleaning Cleaning the fluff filter The fluff filter must be cleaned after each load. If you have very hard water, this can cause limescale deposits in the fluff filter. Check for any limescale deposits when cleaning the fluff filter and, if necessary, wash down the filter by hand. Pull the filter out of its holder. Cleaning the outside of the machine Clean the outside of the machine and the programme panel with a mild cleaner. Keep the area around the tumble dryer clean and cool; dust, heat and moisture prolong drying times. 2 1 3. If you have hard water, the filter should be washed down with water to get rid of any limescale deposits. Dry the filter carefully with a towel. 13 Troubleshooting The machine will not start Check · that the outer door is properly closed · that the main power switch is pressed · that you have set the programme correctly · that the Delayed Start option has not been selected. Remember that the tumble dryer produces heat and should therefore not be located in a room that is too small. [. . . ] Unscrew the two screws on the sides of the door, around five millimetres, to allow the door magnet and cover washer on the inside of the door to be removed. Next you must move the plastic plugs on the upper and lower edges of the door. Angle the lower edge of the door out to the left while turning the hinge attachment as indicated by the arrows. Hinge attachment 3. For right hanging, the hinge attachment must then be turned upside down. 2 Hinge pin 8. [. . . ]